Extension springs are long, lighter-weight springs that run perpendicular to the door and are mounted above the horizontal portions of the door tracks. These springs are tensioned by stretching out, using cables and pulleys, as with the torsion system. Because extension springs are merely suspended between two brackets (they are not mounted to a rod, like torsion springs), they must have a safety cable running through each spring. This helps contain the spring in the event of a breakage. Without the safety cable, a spring breaking under tension is a very serious safety hazard. If you have old springs that don't have safety cables, you should install them even if you aren't replacing the springs.
On average, to have your springs replaced on your garage door will vary anywhere from $200 to as much as $400 if you were to hire a professional.  Breaking the costs down, the springs, depending on the part needed and the size, will cost about $20 to $60 each.  Add in the labor, which can be $45 to $85 per hour, depending on your location, can bring the grand total to the estimate noted.   A tilt-up door, on average, will be about 20 to 30 percent less than a roll-up door.

9.6 Bending the cable will help you avoid problems with the tip at the end of the cable catching on the end bearing plate and causing the cable to come off and the garage door to jam, cock, or fall. Check to make sure the cable is straight in the slot and not sticking out the side. Also the edge of the cable stop should not be pointing to the side as displayed. The cable tip should fit completely inside the drum, with the rounded part facing out so the tip can't scrape the end bearing plate.

Would have appreciated the technician to have explained in better detail about the quality of the first doors we received in our home. The garage doors that were installed recently were an upgrade. I would have selected the better quality of doors with the first installation if it had been explained in better detail and time of decision with the first doors. But, I really love the doors that were recently installed! Explained much better with the new doors. Time was well spent on my decision making and the technician this time was very helpful and knowledgeable. Thank You! Cathy Walsh


Unfortunately, if the metal contraction happens quickly — for example, after a rapid freeze — the contraction may actually cause your door track to bend. This is a much more serious problem, and may require repairs further down the road. However, if the bending in your track is minor, your door will still function properly, even if it does make a little more noise.
A standard double garage door is 7 ft. high by 16 ft. wide. Standard single doors are 7 ft. high by 8 or 9 ft. wide. Because the doors are so large, few home centers and only some garage door stores keep many doors in stock, so expect to order one instead of buying it off the shelf. Garage doors are available in wood, fiberglass and steel. Steel doors, like ours, are light, maintenance-free, affordable, readily available, and have an insulating value as high as R-19.

Garage Door Repair Images Centennial Co 80016


It you have a tilt-up door, you are looking at a $150 – $200 repair or replacement. If it’s a roll-up door it’s going to cost you more. Roll-up door spring repair or replacement is usually around $200 – $250 for a 2 car door. If the brackets need to be disassembled to remove the springs due to the shaft not sliding sideways enough it will cost you an additional $50 – $100.


To install a single new garage door it should cost between $500 and $800. They demonstrate that the average homeowner can usually tackle such a project in a nine hour time span and a professional will be able to complete it in roughly five hours. Should it be a DIY project? Not really, most housing experts point out that it is a two-person job, requires advanced carpentry skills, and even knowledge of household electronic systems.
There’s nothing more frustrating than attempting to open or close your garage door only to find that it simply won’t budge. In some cases, your garage door may even open or close halfway only to get stuck in the process. The very first thing that you should do if your garage door seems to be stuck is to check the batteries in your remote. You’d be surprised at how often this is the root of the trouble. If dead batteries were not the issue, then use the following four tips to further troubleshoot your garage door.

Garage Door Repair Free Quote Centennial 80015


10.4 Raise the second bar 90 degrees and insert the first bar. This is "three." Continue winding. If the spring shortens in length, unwind the spring and switch sides - the springs are on backward. Otherwise, continue winding until you reach a count of "30." This is 7 1/2 turns, which is normal for most 7' doors. Longer life springs are wound the same number of turns. Newer steel doors with only one strut on top often need only 7 1/4 turns. On 8' doors count to 34. Each time you insert a bar into the winding cone, listen for the click to let you know the bar is in all the way. Not inserting the bar all the way could cause the cone to explode.

Garage Door Repair Guy Centennial Colorado 80016


Scott was exceptionally polite, professional and knowledgeable. He thoroughly checked my garage door opener, but also inspected the garage door itself and pointed out rust and deterioration that has occurred. Scott then gave me a quote on a new garage door, explaining the installation procedure and quality elements of the new door including the warranty. I was very pleased with the entire service appointment, and my husband and I are seriously considering the new garage door, but only if Scott is the installer! Thanks, Scott!
If your stuck garage door coincides with weather changes, you may need to adjust the pressure on the opener. Some openers have a force-adjustment mechanism that controls the force that's applied to operate the door. It's best to leave this adjustment to a garage door pro, as too much force may result in the door failing to stop when it should, posing a danger to people and objects in the door's path.
9.15 Install the bolts to secure the stationary center cones to the center bracket. Position the shaft here so it is the same distance from the header as the shaft is at each end. Finger-tighten the nuts until the stationary cones are flush against the center bearing plate. Forcing the cones by tightening the bolts may break a cone if it is catching on a bearing. Winding torsion springs with cracked cones can cause the springs to spin loose and the bars to fly. Secure the bolts.

Whether you need a new garage door spring, a damaged door panel replaced, a new opener installed or a track or rollers replaced, with over 25 years experience in the garage door repair business, I can get it done for you.  Many customers are also happy to know that all the garage door springs I use are not only "Made in the USA", they're made right here in Arizona!  We like to keep things local, and we hope you will do the same when you need a garage door repair for your home.
SNAP... bang... boom. That is the sound of a garage door torsion spring breaking. It can be a very loud noise that sounds like a firecracker or gunshot. Springs are rated for a certain number of cycles and are the first thing that will break in your garage door assembly. Broken springs are the #1 source of customer calls for garage door repair companies. If you have a broken spring, you should NEVER try to open the door, as it can be very dangerous. This repair should be left to a professional or someone with the right tools and skills.
However, if you lose power and use the disconnect switch, you’ll need to reattach it to use your garage door motor to open and close your door again. Open the door all the way and then reattach this hook. Then try opening or closing the door again with your transmitter, and you should be all set. It will be easiest to reattach this hook when your car is not in the garage, as you’ll need to place a step ladder underneath the motor to reach it. 
×