You may enter your information on this website, visit an in store associate or call our garage door repair team at the number at the top of this page. Within 24 hours you will receive a call from a local service provider to discuss your requested service. Afterwards, you will schedule a date and time for the service provider to come to your property.

With Garage Door Doctor, you can rest assured we will replace your springs correctly. We offer 2 types of springs – standard and high cycle. On a 7 foot tall door, our standard torsion springs will last 15,000 cycles and our high cycle torsion springs will last 50,000 cycles. How many years will this last you? That is based off only one thing – usage. For example, with standard torsion spring, if you use your door 4 times a day, you get just over 10 years of life. However, if you use your door 8 times a day, you would get just over 5 years of life. If you use door very little or if you are moving very soon, maybe standard springs would be best for you. If you use your door many times a day or if you don’t plan on moving for a while, high cycle springs would be best for you. Getting high cycle springs will ensure you won’t be stuck with a broken spring for many years to come. Either way, both types of torsion springs we offer work great – its just a matter of when the break again. Call Garage Door Doctor today to have your garage fixed properly!


Determine the inside diameter of the spring and the size of the coils. Run a tape measure across the opening at one end of the spring. Carefully measure the inside diameter of the spring so you can provide the supplier with this information. Then, use a tape measure to find the length of 10 coils on the spring. Divide the length by 10 to determine the measurement of a single coil.[7]

Garage Door Repair And Service Centennial Colorado 80015


Using your drill, add tension to the torsion spring. This system uses a single spring for a double door, but many manufacturers use two springs for a double door. The painted line on the spring acts as a gauge for the number of turns you put on the spring. To keep the bar from turning while you’re adding tension, attach a locking pliers to the bar on both ends of the spring. Apply lubricant for garage doors to the spring.
Opening the door yourself is recommended only during an emergency, as there is an increased risk of it getting stuck again-or worse yet, crashing down on top of you. Moving a wooden door could cause damage to the opener, or the top of a steel door might bend underneath the pressure. If you must open the door long enough to drive underneath it, you may want to prop up either side with some 2×4 pieces of lumber to provide added stability. You could also secure your door to its tracks using a pair of vise grips or a couple of c-clamps.
Garage door springs can break for a variety of reasons. Extreme heat or cold, for instance, can stress the springs to the point of breaking, or it could be that normal wear on older springs could cause them to break. Whatever the situation, a broken spring can render your garage door inoperable. Your door will not be able to open or close when a spring is broken, and you should stand clear of your door until a professional can assess the situation and correct it.
First, check to see if the transmitter on the wall inside your garage still opens your garage door when pressed. If it does, then the transmitter in your car likely just needs a simple battery replacement. If you have more than one car transmitter for your garage door, then your other transmitters will likely need new batteries soon as well, since they were probably installed around the same time.
The technician did a wonderful job - arrived on time and completed the job in less than 2 hours. I would have given him a 5 on everything if he had returned to add the additional piece (a piece that is fixed to the door frame for better insulation) to my door on the outside on the day he said he would come back. The piece he brought was of wrong color and he said he would be back with the right color the first day after New Year's Day to put up the piece. I hope he can come back soon.

Garage Door Repair Installation Centennial 80016


If the engine of your garage door opener isn’t working properly, then your garage door probably won’t be working properly. If your garage door gets stuck and you hear a grinding sound coming from the garage door opener, then there’s a good chance that there is an issue with its engine. That issue is that the main drive gear probably needs to be replaced. The main drive gear is most common of the garage door opener’s components to fail. It is a plastic gear that takes some know-how to remove and replace, which is why you should strongly consider hiring a professional garage door repair service for this particular issue.
Dallas Texas, Plano TX, Garland TX, Highland Village, Lakewood, Las Colinas, Lewisville, Little Elm, Grapevine, Haltom City, Hurst, Keller, Forney, Carrollton, McKinney TX, Murphy Texas, Oak Lawn, Arlington TX, Parker TX, Plano, Preston Hollow, Richardson TX, Denton, Addison, Allen, Bedford, Coppell, Crowley, DeSoto, Euless, Flower Mound, Rockwall Texas, Garland Texas, Rowlett TX, Sachse TX, The Colony TX, Lavon Texas, Fort Worth TX, East Dallas, North Dallas, Wylie TX, White Rock Lake, area Lakewood, North Richland Hills TX, Benbrook, Burleson, Waxahachie, Red Oak, Irving TX, Mesquite TX

Garage Door Repair And Installation Centennial 80016


6.7 It's now time to unwind the spring. Firmly position yourself on a steady ladder beside the garage door. Next, insert the bar into one of the holes of the winding cone. Make sure it goes all the way in. It should click when your bar hits the core. If you want to test the force you will be handling before loosening the set screws, push up on the bar one quarter turn and bring it back down. Next, while grasping the other end of the bar firmly, loosen the set screws with an open-end wrench or small adjustable wrench loose enough to come free should the cone spin. Be prepared for the torque to be transferred to the bar.
Gather the supplies and tools needed for changing the springs safely. In addition to the torsion springs you'll need a minimum of one or two 10" vise grips, an adjustable wrench, and two 1/2" X 18" winding bars. Most hardware stores sell 1/2" X 36" steel rods that can be cut in half. You'll also need a firm ladder and a rag for cleaning your hands. A ruler and a file may also be necessary; a socket wrench and sockets would shorten the time required. Finally, make sure your garage is lighted well.

If you have decided to replace your springs, if you are sure your door had the correct springs, and if you are ready to buy new ones, we recommend that you measure your spring or springs following the instructions in Step 4 below. Measuring springs can be difficult; most individuals, even garage door technicians, sometimes have difficulty measuring torsion springs. Ordering incorrect springs wastes time and money.
Gather the supplies and tools needed for changing the springs safely. In addition to the torsion springs you'll need a minimum of one or two 10" vise grips, an adjustable wrench, and two 1/2" X 18" winding bars. Most hardware stores sell 1/2" X 36" steel rods that can be cut in half. You'll also need a firm ladder and a rag for cleaning your hands. A ruler and a file may also be necessary; a socket wrench and sockets would shorten the time required. Finally, make sure your garage is lighted well.	

In addition to the bodily risk involved, it’s simply not an easy task. There’s the possibility that you will not install it correctly. At worst, this creates the risk that the mechanism will fail at the wrong time and injure you or someone in your family. At best, this means it will malfunction, and you’ll have to call professionals to fix it. It will save time, money and potential heartache to simply call a professional to install your new door springs correctly the first time.


Just like on a bike sprocket, your cables can sometimes become disengaged. Oftentimes, when a torsion spring breaks, the garage door cable will snap as a result. Sometimes, the cable will cause damage to a vehicle or wall, and if a person happens to be in the way of the cable it can cause serious harm. If you cables have snapped, you should call a professional to help you. See the video above.
Interested in garage door installation? You don’t have to know how to install a garage door or how to install a garage door opener. Lowe’s has you covered with professional, independent garage door installers to manage the job from taking measurements to the final garage door opener installation. Why take the time to learn how to install garage doors or how to install garage door openers? Invest less time and manage garage door installation costs. Contact Lowe’s for your project services today.
While it would be wonderful if door springs lasted forever, the reality is that the simple act of opening and shutting the door multiple times every day isn’t easy. It’s hard on the springs, even though they’re built to do it. Most springs will last for a while, but they won’t last forever. The regular wear and tear of endlessly opening and shutting the door breaks them down and eventually, they’ll need to be replaced.
Scott was exceptionally polite, professional and knowledgeable. He thoroughly checked my garage door opener, but also inspected the garage door itself and pointed out rust and deterioration that has occurred. Scott then gave me a quote on a new garage door, explaining the installation procedure and quality elements of the new door including the warranty. I was very pleased with the entire service appointment, and my husband and I are seriously considering the new garage door, but only if Scott is the installer! Thanks, Scott!

Garage Door Repair Average Cost Centennial Colorado 80016


After you’ve ordered your new garage door, we’ll perform a site inspection to confirm your door size. We’ll contact you to schedule the installation, and our professional installers will do the rest. They’ll deliver your door, take down the old door, reconnect your opener if there is one, seal your perimeter and provide a final walk-through where they’ll clean up the area and haul away your old door. Additional fees for haul away may apply in some markets. We are happy to provide answers to questions you may have at the time of your garage door and opener installation. https://www.youtube.com/watch?feature=youtube.be&v=Z_eZc-kh40c
On average, to have your springs replaced on your garage door will vary anywhere from $200 to as much as $400 if you were to hire a professional.  Breaking the costs down, the springs, depending on the part needed and the size, will cost about $20 to $60 each.  Add in the labor, which can be $45 to $85 per hour, depending on your location, can bring the grand total to the estimate noted.   A tilt-up door, on average, will be about 20 to 30 percent less than a roll-up door. http://www.youtube.com/v/Z_eZc-kh40c

7.3 Slide both torsion springs out above the top of the garage door toward the cable drums. Notice that there is only one bushing or bearing between the cones. Sometimes a single bearing is pressed into the bracket; other brackets have a single bearing or bushing that fits in either cone. Do not try to install a bushing or bearing in both of the stationary cones. You will risk breaking a cone. The purpose of the bushing is to keep the shaft from wearing against the spring anchor bracket. Only one bushing is needed to accomplish this.

Garage Door Repair Images Centennial Co


9.15 Install the bolts to secure the stationary center cones to the center bracket. Position the shaft here so it is the same distance from the header as the shaft is at each end. Finger-tighten the nuts until the stationary cones are flush against the center bearing plate. Forcing the cones by tightening the bolts may break a cone if it is catching on a bearing. Winding torsion springs with cracked cones can cause the springs to spin loose and the bars to fly. Secure the bolts.
Unfortunately, if the metal contraction happens quickly — for example, after a rapid freeze — the contraction may actually cause your door track to bend. This is a much more serious problem, and may require repairs further down the road. However, if the bending in your track is minor, your door will still function properly, even if it does make a little more noise.
If your door has two springs, most professionals and research online says that replacing both springs is the best option. Most torsion springs are rated for 10,000 close/open cycles. If only one of your springs is broken, both springs are still recommended to be replaced. Considering that your second spring will break soon anyways, this added on fix is only going to cost you about $50 extra to assure that you don’t have to pay another service fee for a second visit.
Next, if you don’t find an obstruction, check the springs. If your door has torsion springs, which are horizontal at the top of the door, you can tell they are broken by checking for a gap between the two springs. If your door has extension springs, you can check by looking to see if they are hanging on the side of the door. If you have a broken spring, you’ll need to call a pro to replace it as this is a dangerous task.
Replacing torsion springs is done with the door closed. You start by carefully unloading all of the springs (most standard-size doors have two; any broken spring will already be unloaded), using the winding bars. Then, you unbolt the springs from the central rod bracket, disconnect the cables from the pulleys, and loosen the pulleys and slide them off of the rod. Next, you swap out the springs, reinstall the pulleys and cables, and secure the inside ends of the springs to the central bracket. Finally, you wind up both springs (securing them with two setscrew bolts on the winding cones) and test the door for proper spring tension. Often, springs need an extra quarter-turn or two to get the door balance just right.
8.10 Double-check to make sure you have the correct wind on your new torsion spring. On the left side next to the winding cone the end of the spring wire should be pointing up if it is facing you. Notice, also, that the cone is red which usually designates right wind. Customers frequently call and explain that when they get about six turns on the springs they spin on the cones. This is due to installing the springs on the wrong sides of the center bracket. https://www.youtube.com/watch?v=Z_eZc-kh40c&app=mobile
In order to prevent injury, garage doors automatically reverse if they come into contact with an obstacle. When the door closes halfway but then reverses for no apparent reason, this may be a sign that there is something preventing it from closing, something that you can't see. Check the tracks for stuff like dirt, rocks, bits of trash, or other debris. Give the tracks a wipe-down to dislodge anything that might be getting in the way.

In need of garage door repair? Contact one of our many well-trained garage door repair professionals today to provide your garage door system with the recommended service and maintenance procedures for smooth and reliable operation. Our garage door repair professionals are here for you, whether you want to fix your existing garage door or buy a new garage door. Are you looking to replace a garage door spring, cable or roller or searching for 'garage door repair near me'? Use our distributor locator below: 
It is very important that the replacement springs are calibrated for the weight of your door. Using the wrong size garage door springs will caused the to not function properly and could also cause the opener to break much quicker. Replacing extension springs can be very dangerous and if done wrong can harm someone using the garage door. Make sure you call the Garage Door Doctor to ensure your garage is repaired properly!
10.2 Tape your winding bars if you have not done so already, not only to assure that you are inserting the bars completely into the cones as you wind the torsion springs, but more importantly to assure that the bar does not slip out of the cone when you stretch the springs at the end. This has happened to me several times. Professionals always stretch torsion springs after winding them because the shaft floats horizontally between the flexible end bearing plates as the door operates. Although this may be as little as 1/4", the binding of the coils as the garage door closes oftentimes keeps the door from closing completely, especially when the torsion springs and bearings are dry.
Your door’s torsion spring is located approximately one foot from the top section of your door when it is closed. It consists of two large coil springs, and is approximately the length of your arm. Its purpose is to balance the weight of your door so that a door weighing between 160 and 185 pounds is practically weightless to lift. As such, it makes it possible for a garage door opener to raise the door using only ten pounds of pressure.

Garage Door Repair Cost Centennial Co 80015


I went on Garage Door Nation website to look at the conversion chart from 1 to 2 torsion springs. For my 1 spring, size 2"/0.250ID/30.5" length, they recommended 2 of 2"/0.207ID/24" length. I got this kit from Amazon for $64 with $11 overnight shipping even though I could get free shipping through Prime over the weekend, but I couldn't wait for 3 more painful days. Installed it followed YouTube video. Worked better than my old one, a lot quieter. Check the video if you want to install one yourself. Professional installation costs hundreds of $$$:

Garage Door Repair Cost Centennial Co


Determine the inside diameter of the spring and the size of the coils. Run a tape measure across the opening at one end of the spring. Carefully measure the inside diameter of the spring so you can provide the supplier with this information. Then, use a tape measure to find the length of 10 coils on the spring. Divide the length by 10 to determine the measurement of a single coil.[7] https://youtu.be/Z_eZc-kh40c
My garage door torsion spring broke so I decided to replace it myself. Shipping was next day. I got the torsion spring rod at a local hardware store. Easy to install once I figure out how to lock down the rod from moving and loosening the door cable on the side. Instructions tells you how to do it. Great replacement spring and save $$$ doing it myself.
Since most yards entertain play activity including baseballs and other sporting equipment, it's no surprise that garage doors experience broken glass from time to time. Regardless of the cause, it's important to repair glass quickly, since broken glass in a garage is a safety issue, a security problem, and an invitation to every bird and insect in the neighborhood to take up residence in your garage. Fortunately, it's not difficult to replace a pane of glass. The techniques are exactly the same as for replacing glazing in a house window.

On one-piece doors with side springs, you open the door to relieve the spring tension, and simply swap out the springs on the opener-arm mechanism; there are no cables or pulleys to deal with, and the springs have internal safety rods. Some doors have tensioners that maintain moderate tension when the door is open all the way, and on these you'll have to loosen the tensioner in order to remove the spring.

Garage Door Repair Free Estimate Near Me Centennial 80015


On average, to have your springs replaced on your garage door will vary anywhere from $200 to as much as $400 if you were to hire a professional.  Breaking the costs down, the springs, depending on the part needed and the size, will cost about $20 to $60 each.  Add in the labor, which can be $45 to $85 per hour, depending on your location, can bring the grand total to the estimate noted.   A tilt-up door, on average, will be about 20 to 30 percent less than a roll-up door.
	2.4 The same is true of Older Overhead, BarCol and Raynor torsion springs that have winding cones with inconsistent hole sizes. If you insert a 1/2" X 18" bar in some of these holes you can move the opposite end of the bar over four inches. Bars in newer cones move less than 1 1/2". I've had many of the older cones spin loose from my bars, the last one generating an $1800 emergency room bill. If your cones are like any of these, or if they have more than 2" of play, leave the job of installing torsion springs to a professional garage door mechanic.

All measurements should be in feet and inches. Step 1, measure across the existing door or desired space for the width, then up and down for the height. The rough opening of your space should be the same size as the door. Step 2, measure the sideroom, which is the space beside your door. Measure the width of the left side, and then the width of the right side. Step 3, measure the space above the door, which is called the headroom. Measure the height of the distance between the top of the door opening and the ceiling. Step 4, measure the ceiling, which is called the backroom. You’ll need to measure the distance of the garage door opening toward the back wall of your garage. You should have 6 total measurements in all once you’ve finished measuring the space. Keep in mind that having an automatic garage door opener installed might call for additional backroom or ceiling space.
Luckily, there is a bit of science to questions of garage door repair and replacement. That’s why we’ve put together this guide on when to replace a garage door. We’ll prepare you to compare repair vs replacement garage door costs. We’ll discuss the ways in which repairs are the most affordable option while also exploring those moments when replacement will in the end provide you with more value added.
Maybe the battery died or a spring broke, but you can't get into the garage to even see what the problem is. If the garage door is the only way in or out, or if you can't find the key to the door, you'll have to either find a way to break in or call a locksmith. As a preventative measure, it's smart to keep a spare key or install an emergency key release that would allow you to release the emergency disconnect to the operator so you can manually raise the door. https://youtube.com/e/Z_eZc-kh40c?app=desktop
If your garage door is equipped with extension springs (usually seen on single car garages), the cable and pulley might be hanging down when the spring break's. Extension springs use a two pulley system on each side of the door to lift the garage door up and down. When the spring break's everything goes haywire, causing the cables to become twisted or even frayed when they catch on the metal edge of the track. There is a lot of force being released when a garage door spring breaks.
Given the complexity of a garage door and opener system, there are a variety of different areas something could go wrong. If your garage door shakes or is very loud during operation, the garage door closes all the way only to immediately open back up, the garage door opens slowly or closes too quickly, or the garage door opener and remote aren't working at all, you should seek help from a professional garage door repair specialist.
If your garage door isn’t operating properly, the torsion springs are likely to blame. If you’re concerned about tackling this project on your own, consider hiring out the job to a professional. Otherwise, replace both the left and right springs at the same time to save yourself from having to do the job twice. Remove the old springs and measure them while they’re relaxed. Only then will you be able to order replacement parts and install the new springs. Replacing your own garage door springs takes only a little time and effort and can save you hundreds of dollars.
Adding a new garage door provides a dramatic difference in your home’s appearance. When neighbors pass by, when guests pull up, or when you return from work, your house will have a distinct beauty that makes it a landmark of the neighborhood. The unique look you’ve always imagined — as well as the material, the finish, and the insulation can be found in our wide selection of garage doors.
These instructions are for doors with cable drums and cables that look similar to those in the picture below. The next part beyond the end of the spring assembly is the cable drum. The drum is cast aluminum alloy 4" in diameter and 12.6" in circumference around the flat portion. Just beyond the cable drum is the end bearing plate. The cable unwraps off the back of the drum between the drum and the garage wall or jamb and travels down alongside the door, inside the track brackets and behind the roller stems as shown.
10.4 Raise the second bar 90 degrees and insert the first bar. This is "three." Continue winding. If the spring shortens in length, unwind the spring and switch sides - the springs are on backward. Otherwise, continue winding until you reach a count of "30." This is 7 1/2 turns, which is normal for most 7' doors. Longer life springs are wound the same number of turns. Newer steel doors with only one strut on top often need only 7 1/4 turns. On 8' doors count to 34. Each time you insert a bar into the winding cone, listen for the click to let you know the bar is in all the way. Not inserting the bar all the way could cause the cone to explode. https://m.youtu.be/Z_eZc-kh40c
When one or both springs break, gravity takes over and you feel the full weight of the door when lifting or lowering it.  It may be possible to pull the door up by hand, although doing so will likely be very difficult. In most cases, two or more people are needed to raise the door high enough for you to drive your car out of the garage. While single garage doors can typically be lifted, double doors are nearly impossible to manipulate due to their excessive weight.

Garage Door Repair Installation Centennial Co 80015


The technician did a wonderful job - arrived on time and completed the job in less than 2 hours. I would have given him a 5 on everything if he had returned to add the additional piece (a piece that is fixed to the door frame for better insulation) to my door on the outside on the day he said he would come back. The piece he brought was of wrong color and he said he would be back with the right color the first day after New Year's Day to put up the piece. I hope he can come back soon.

Garage Door Repair Installation Centennial 80016


Whether you need a new garage door spring, a damaged door panel replaced, a new opener installed or a track or rollers replaced, with over 25 years experience in the garage door repair business, I can get it done for you.  Many customers are also happy to know that all the garage door springs I use are not only "Made in the USA", they're made right here in Arizona!  We like to keep things local, and we hope you will do the same when you need a garage door repair for your home.
If you’ve tested and tried to remedy these other problems and you’re still having issues, you may need to reprogram your transmitter. All transmitters have a learn button somewhere on the remote, so first you’ll need to locate that on your transmitter. Press and hold the learn button for a few seconds until the indicator light starts blinking. While the light is blinking, press your remote button again to reprogram that remote.

Garage Door Repair How Much Centennial Colorado 80015


My garage door torsion spring broke so I decided to replace it myself. Shipping was next day. I got the torsion spring rod at a local hardware store. Easy to install once I figure out how to lock down the rod from moving and loosening the door cable on the side. Instructions tells you how to do it. Great replacement spring and save $$$ doing it myself.
Your springs may be broken. There are two different types of springs. If your garage door springs are located horizontally at the top of your garage door then it is called a torsion spring. You should check for a gap in between the springs to indicate if they are broken. If your springs are located at either side of your garage door, they are called extension springs. Look to see if a piece of them is hanging on the side of your garage door to indicate if those are broken. If your garage door springs are broken then replacing them is a dangerous process if you have never done it before so you should seek a professional to repair or replace them.
Door styles - in addition to the styles just mentioned, it is important to also consider additional features such as windows across the top of the door to provide light inside of the garage, the use of steel or wood frames to give decorative doors added security and stability, and insulation which can reduce energy costs in the attached garage by an impressive 15 to 20%; and
Just like on a bike sprocket, your cables can sometimes become disengaged. Oftentimes, when a torsion spring breaks, the garage door cable will snap as a result. Sometimes, the cable will cause damage to a vehicle or wall, and if a person happens to be in the way of the cable it can cause serious harm. If you cables have snapped, you should call a professional to help you. See the video above.
×