Loosen the set screws while holding each spring with a winding bar. Position a sturdy ladder to the side of the springs, rather than working directly in front of them, for safety reasons. Put on eye protection and leather gloves. Push a winding bar into the bottom hole of the winding cone on the outside of 1 spring. Use a wrench to loosen the 2 set screws. Keep a firm grip on the bar as the the spring will expand powerfully as the screws are released. Repeat on the other side.[2] 

Garage doors eventually begin to break, look terrible and pose safety risks. How old is your garage door? Have you ever had a safety inspection performed? Garage door safety should always be a top priority as it could cause serious injuries and cost you the expense and trouble of personal injury lawsuits. Our blog will show you what you need to know about garage door safety inspections to assist you with the inspection and upgrades of your home's garage door. Hopefully, what we show you will help to keep your friends and family safe from harm when they visit you.
Prices, promotions, styles, and availability may vary. Our local stores do not honor online pricing. Prices and availability of products and services are subject to change without notice. Errors will be corrected where discovered, and Lowe's reserves the right to revoke any stated offer and to correct any errors, inaccuracies or omissions including after an order has been submitted. https://www.youtube.com/watch?feature=youtube_gdata&v=Z_eZc-kh40c
You may remember a time as a kid when you and your siblings would close the garage door and run underneath it as fast as possible to make it out before the door closed. Well, on any garage door installed after 1993, that’s no longer possible thanks to two tiny photo eyes on either side of the garage entrance. These photo eyes transmit an invisible beam between each other that detects if anything is in the garage door’s path when it closes. This safety measure is there to prevent automatic garage doors from closing on top of someone or something and causing serious injury or damage to property.
Once the lock switch has been activated, you can only control the garage door via the wall control unit. You may have forgotten to de-activate it after coming home from an extended period away, which is why the garage door seems to be stuck whenever you attempt to use your remote. Check to see if this is the case and simply unlock your remotes by pressing the lock switch again.

There are several retailers that sell garage door springs and their parts. Local hardware stores often carry a selection of lubricants, torsion conversion kits, safety cables, ball bearings and extension springs. Another option is a garage door supply company or an online retailer that will usually offer a more extensive inventory. These retailers sell everything from lubricant to torsion-spring conversion kits and garage door tools. They also tend to offer information to their customers and help them locate the parts they need and understand how to complete a specific repair.


If the door only goes up six inches and stops, or moves very slowly when using your remote, you could have a broken spring as well. Some customers will notice that the top section of their door is bent or that the door falls very quickly when lowering. Your door may be “crooked” or jerky when going up and down, and both of these signs indicate your torsion spring is in poor condition and very likely to break in the near future. Any time you hear a loud “popping” noise while operating, you should inspect your torsion spring immediately for signs of damage.
"Springs get a lot of wear and tear because they handle the weight of the door," says Paul Cardone, owner of Garage Door Guru in Charlotte, North Carolina. "The type of spring you have depends on the type of door you have — the heavier the door, the more heavy duty the spring. They're full of tension and made of metal, so after so many cycles, they just snap and break."

Garage Door Repair Estimates Centennial Colorado


Atkins studios Garage Doors was referred to my husband on January 27, 2018. Our garage door came off the track. James came and responded to the job within two hours. He is a very honest and fair priced person to deal with. He is located in Palm Coast. I got estimates from other garage door repair people and they were way out of the ball park with their quotes.
I went on Garage Door Nation website to look at the conversion chart from 1 to 2 torsion springs. For my 1 spring, size 2"/0.250ID/30.5" length, they recommended 2 of 2"/0.207ID/24" length. I got this kit from Amazon for $64 with $11 overnight shipping even though I could get free shipping through Prime over the weekend, but I couldn't wait for 3 more painful days. Installed it followed YouTube video. Worked better than my old one, a lot quieter. Check the video if you want to install one yourself. Professional installation costs hundreds of $$$: 

Garage Door Repair Cost Centennial Co


Step 2: Check the tracks with a level to make sure they're properly aligned. Horizontal tracks should slant slightly down toward the back of the garage; with roll-up doors, the vertical sections of track should be exactly plumb. Both tracks must be at the same height on the garage walls. If the tracks are not properly aligned, loosen but do not remove the screws or bolts that hold the mounting brackets, and tap the tracks carefully into position. Recheck the tracks with the level to make sure they're in the right position; then tighten the screws or bolts at the mounting brackets.

Garage Door Repair Average Cost Centennial 80016


Determine the inside diameter of the spring and the size of the coils. Run a tape measure across the opening at one end of the spring. Carefully measure the inside diameter of the spring so you can provide the supplier with this information. Then, use a tape measure to find the length of 10 coils on the spring. Divide the length by 10 to determine the measurement of a single coil.[7]

Garage Door Repair And Service Centennial Colorado 80015


It you have a tilt-up door, you are looking at a $150 – $200 repair or replacement. If it’s a roll-up door it’s going to cost you more. Roll-up door spring repair or replacement is usually around $200 – $250 for a 2 car door. If the brackets need to be disassembled to remove the springs due to the shaft not sliding sideways enough it will cost you an additional $50 – $100.
2.1 Two important assumptions will help you execute this replacement safely. First, assume that the springs are going to break as you unwind or wind them. To avoid injury, clutch the bars firmly on the ends furthest away from the cones and stand securely on a sturdy ladder, not on chairs or cans turned upside down. Keep clothes and body parts away from the springs. Wear safety glasses. https://youtube.com/watch?feature=player_embedded&v=Z_eZc-kh40c
There’s another reason new doors are superior to old ones: energy efficiency. Keep in mind, garage doors are large, and when they open, they let a lot of outside air into your home. While you may have significant insulation separating your garage from the rest of your home, eventually that temperature differential will start to influence your energy bills.

Garage Door Repair Free Quote Centennial 80016


DIYers are generally steered away from working with torsion springs because installed springs are always under tension. To safely remove a torsion spring, you have to control the tension by holding the spring with a solid metal winding bar, then you loosen the spring from the rod and manually unwind the spring using two winding rods. The spring is potentially dangerous until it is fully unwound. By contrast, extension springs have little or no tension when the garage door is fully open.

Automatic Garage Door Repair Centennial Colorado 80015


If the track is misaligned, but the door still moves, there are a few things you can do to attempt to remedy the issue on your own. You’ll know that it’s misaligned if you hear a rubbing noise when the garage door reaches a certain spot on the tracks each time it opens and closes. Sometimes the door may even slow down slightly when it hits this spot.

Determine the inside diameter of the spring and the size of the coils. Run a tape measure across the opening at one end of the spring. Carefully measure the inside diameter of the spring so you can provide the supplier with this information. Then, use a tape measure to find the length of 10 coils on the spring. Divide the length by 10 to determine the measurement of a single coil.[7]
Once the lock switch has been activated, you can only control the garage door via the wall control unit. You may have forgotten to de-activate it after coming home from an extended period away, which is why the garage door seems to be stuck whenever you attempt to use your remote. Check to see if this is the case and simply unlock your remotes by pressing the lock switch again.
DoItYourself.com®, founded in 1995, is the leading independent home improvement and repair website. We welcome your comments and suggestions. All information is provided "AS IS." Website operating problems contact [email protected] Questions of a Do It Yourself nature should be submitted to our "DoItYourself.com Community Forums". Copyright© 1995-2018 MH Sub I, LLC dba Internet Brands. All rights reserved. You may freely link to this site, and use it for non-commercial use subject to our terms of use. View our Privacy Policy here.

Carter door: Garage doors in Florida come with extra bracing on the back and are wind-loaded to protect against hurricanes. The average with is 350 lbs. but some can weigh as much as 800 lbs. It can cost up to $1,000 dollars to replace a steel two-car garage door and if it’s made of wood it can cost you up to $5,000 dollars. Some customized doors can be as much as 20 – 30k.
The tricky parts of the job involve you carrying the tension of the spring. Replacing a spring requires that you first unwind the spring to relieve the tension, then wind it back up and secure it while it's under tension. Winding bars are used for all winding and unwinding actions—don't try to save a few bucks by substituting long screwdrivers or pieces of rebar for the real winding bars. Substitute tools are much more likely to slip, or they may bend or break under the load of the spring.
Automatic doors require not only the installation of a heavy door, but the motor and cables as well. Automatic doors are much more common now because of their convenience, but in a case such as the heavy wood door, they are a necessity. A strong motor is required to pull up a heavy door. However, automatic doors are not without their faults -- they quickly become a manual door when the power goes out.

Locating a contractor - there are many professional overhead garage door companies. It is always advisable to contact at least three different agencies and request a bid or quote for the work. Be sure that each quote includes the costs for a few different types of doors, any installation fees, and the cost of wiring the electronic openers. Standard prices range from: http://youtube.com/watch?feature=player_embedded&v=Z_eZc-kh40c

9.16 If you cannot get the stationary cones to finger-tighten against the center bracket, we recommend installing washers between the winding cone that houses the bearing and the spring bracket. This is a common problem with torsion springs on older Windsor garage doors because their steel bearings are often wider and they extend beyond the stationary cone. Raynor garage doors also have wider bearings that fit properly in their 2 1/4" stationary cones, but washers may need to be installed if their bearings are installed in 1 3/4" or 2" stationary cones, or if some of their older bearings are installed in their newer cones that are installed on older brackets.
If the door only goes up six inches and stops, or moves very slowly when using your remote, you could have a broken spring as well. Some customers will notice that the top section of their door is bent or that the door falls very quickly when lowering. Your door may be “crooked” or jerky when going up and down, and both of these signs indicate your torsion spring is in poor condition and very likely to break in the near future. Any time you hear a loud “popping” noise while operating, you should inspect your torsion spring immediately for signs of damage.

9.8 Twist the garage door shaft to tighten the cable on the drum. While twisting, vise grip the shaft as shown to keep the cable tight on the drum. The top of the vise grip should be tight against the garage header. This will keep the cable snug on the first drum while you install the cable on the other drum and position it in place. It also keeps the shaft from turning and the cables peeling off when you wind the springs. That one grip can save many hours of walking back and forth and having to level and re-level the garage door after winding the torsion springs.
Once you’ve decided it’s time to replace your garage door — whether the result of malfunctions or just seeking to modernize your home’s exteriors — you may be wondering how much a garage door replacement costs. While these numbers are often determined by several factors, including the materials and labor involved, on average, a garage door replacement can cost just over $1,000 but could range from about $300 to over $2,000. https://www.youtube.com/v/Z_eZc-kh40c?version=3
10.13 Slowly pull down on the winding bar until the garage door rises 3" and the roller hits the vise grip on the track. The door will usually drop back down and raise the bar. If it doesn't, lift the end of the bar until the door closes. If the door comes up by itself when you hold the bar lightly, the springs are either over wound or they are too strong. You may need to remove 1/4 to 1/2 turns from the springs. If the door comes up on its own, you either have to many turns on the springs or you have the wrong springs. This can be very dangerous. We recommend getting professional help. Removing the winding bar could cause the garage door to knock you off the ladder.

Nearly every garage door comes with a warranty of some kind. Many companies claim they have a lifetime warranty but don't cover everything. Garage doors have many parts: rollers, cables, springs, door panels, etc. Find out what parts the warranty covers. When you read the fine print, you may find that the warranty does not cover warping, splitting, cracking, denting, or rusting and then limits parts to one year. When shopping you want to make sure you are comparing apples to apples.
ryan was way more than early when he showed up. ryan gave me a straight up, not nonsensical "ah..ah..." like someone making up a story to listen to. direct and to the point, like a professional, gave me my options that i could present to the boss. the boss didn;t like the price of the new rollers. but she loves that it doesn't sound like a tank coming home from war. we were completely unprepared for this, so, it's good we got a guy like ryan.
Whenever a spring breaks, the door will not go up. Attempting to lift a door with a broken spring can be extremely dangerous. Attempting to replace the springs yourself is even more dangerous. You should never attempt to fix a broken spring yourself – only experienced, trained professionals should ever touch torsion springs. Also replacing a spring requires expertise to know exactly which spring to replace it with. The correct springs are determined based off the weight of the door. There are hundreds of combinations of springs but only one is correct for your door. It is important to have the correct springs to prevent an array of problems in the future. With the wrong springs, your opener will break much quicker and your door is more likely to come off tracks. It is alarming how many installers use the wrong size springs. Knowing which springs to use can only be determined by experience.
Many jobs around the house are fairly easy fixes. It’s relatively easy to clean out your fireplace, clean the leaves from the gutters or repaint a wall. It’s a different thing to replace your garage door spring. It’s careful work that is almost impossible to do correctly the first time. Garage door professionals spend a great deal of time learning how to do it properly, and even the most detailed instructions won’t make you an expert in the span of a few hours. It can be almost infuriatingly annoying at times and is simply better left to professionals.
The following procedures are based on my 30 years in the garage door industry. In spite of my high mechanical aptitude, even after 18 years in the trade I lost the end of my left index finger. A few years later I had five stitches in my right thumb, and a year later five stitches in my left thumb. In 2004 emergency room staffs dug steel out of my eye and sewed up my ring finger with eight stitches. The best I can do is help you minimize the risk of injury; that's all I can do for myself. I am not so naive as to think that I have made my last trip to the emergency room. Repairing garage doors, particularly replacing torsion springs, is dangerous work, whether you are a do-it-yourself homeowner or an experienced technician.
We are proud of the work we do in Northwestern North Carolina. We love this community and we love serving it. So whether you think you need a small repair or a major overhaul, we want to be the team that helps you increase the value of your home while making it a safer place to live for you and your family. Our professional and friendly sales team are eager to connect with you, so contact us today and find out just how we can ease your concerns and make transform your garage!
Roberto was very courteous and explained the details of what he was doing. He also pointed out a repair I might consider having done (replacement of the bottom panel of my door) and asked the office to follow up with me on this. Someone did follow up with me and since replacement of the bottom panel is not an option and I would have to replace the door, I decided that I can wait.
Furthermore, newer doors come with more improved security features, helping to improve the way you protect your home and loved ones. While older doors are easy to break into, whether through breaking the lift mechanism or even using a universal garage door remote, new doors come with many redundant security features, which will go a long way in deterring even the most ingenious burglar.

Step 1: Check the metal tracks inside the garage. Look at the mounting brackets that hold the tracks to the walls. If they're loose, tighten the bolts or screws at the brackets. Working inside the garage with the garage door closed, examine the tracks for dents, crimps, or flat spots. If there are any damaged spots, pound them out with a rubber mallet, or with a hammer and a block of scrap wood. If the tracks are badly damaged, they should be replaced.


There’s nothing more frustrating than attempting to open or close your garage door only to find that it simply won’t budge. In some cases, your garage door may even open or close halfway only to get stuck in the process. The very first thing that you should do if your garage door seems to be stuck is to check the batteries in your remote. You’d be surprised at how often this is the root of the trouble. If dead batteries were not the issue, then use the following four tips to further troubleshoot your garage door.

Garage Door Repair Free Quote Centennial 80015


Overhead garage doors weigh hundreds of pounds, and doors that are not properly maintained or which are equipped with older automatic garage door openers can be safety time bombs. All too common are the tragic stories of garage doors injuring or even killing children or pets who found themselves underneath a closing door. Modern automatic door openers with auto-stop and auto-reverse mechanisms have greatly reduced such accidents, but mishaps can still occur if the door and door opener are not properly maintained.

Garage Door Repair How Much Centennial Co


Order replacement springs. Many manufacturers and distributors only provide torsion springs to professionals, and won’t sell them directly to the customer. Luckily, they are available on the Internet, so search online to find replacement springs. Make sure they match the coil size, length, and interior diameter of the springs you removed. Also, be sure to order both a “left-hand” and a “right-hand” spring as the coils are wound in different directions.[8]
×