In this article, we’ll tell you the difference between a safe door and one that’s unsafe. We’ll also give you the helpful tips you’re not likely to find in the manufacturer’s instructions to correctly, and safely, install a new garage door with a torsion spring and do-it-yourself tensioning. Installing a new, double garage door yourself will save you several hundred dollars and should take eight to 12 hours if you’re fairly handy. You can do most of the new garage door installation project yourself, but you should recruit help for removing the old door.
Eric Jonas has been writing in small-business advertising and local community newsletters since 1998. Prior to his writing career, he became a licensed level II gas technician and continues to work in the field, also authoring educational newsletters for others in the business. Jonas is currently a graduate student with a Bachelor of Arts in English and rhetoric from McMaster University.
Roberto was very courteous and explained the details of what he was doing. He also pointed out a repair I might consider having done (replacement of the bottom panel of my door) and asked the office to follow up with me on this. Someone did follow up with me and since replacement of the bottom panel is not an option and I would have to replace the door, I decided that I can wait.
I PAID 700.00 DOLLORS TO GET THE 2 SPRINGE REPLACED WITH TOW DIFFERENT SPRINGS AND BOTH END BEARINGS PLUS INSTATTING THEM. tHIS IS ON A SATURDAY EVENING. aFTER ALL THAT i PAID BY CREDIT CARD THA THE INSTALL COULD SWIPE ON HIS PHONE. hE SAID AT THAT TIME I WOULD RECIEVE MY INVOICE VIA EMAIL. I didn,t think about it until another repair man came today 3/9/16 and he showed me that the bar that goes from one side to the other, had a bow in it of 3 inches just frome one side to the other. With this it will make the new bearings ware out faster. I trusted them to do the job right, But when i called to tell them that they replied that it was passed the 30 day warranty and they would do nothing more.
However, in addition to potentially causing injuries to the under-prepared DIYer, a malfunctioning door can become a safety hazard to you and your family. Keep in mind, according to the National Electronic Injury Surveillance System (NEISS), over 13000 people checked into hospitals with garage related injuries in the United States in 2007. You don’t want to turn a loved one into a statistic just to save a few dollars!
It you have a tilt-up door, you are looking at a $150 – $200 repair or replacement. If it’s a roll-up door it’s going to cost you more. Roll-up door spring repair or replacement is usually around $200 – $250 for a 2 car door. If the brackets need to be disassembled to remove the springs due to the shaft not sliding sideways enough it will cost you an additional $50 – $100. http://www.youtube.com/watch?v=Z_eZc-kh40c&feature=youtube_gdata
Whether you need a new garage door spring, a damaged door panel replaced, a new opener installed or a track or rollers replaced, with over 25 years experience in the garage door repair business, I can get it done for you.  Many customers are also happy to know that all the garage door springs I use are not only "Made in the USA", they're made right here in Arizona!  We like to keep things local, and we hope you will do the same when you need a garage door repair for your home.
If you have a Wayne Dalton TorqueMaster system (pictured below), the springs will be inside a tube. The only way to determine if one is broken is to lift the garage door manually. If the door is heavy (roughly 60lbs for a double car door), you most likely have a broken spring inside the TorqueMaster tube. Another way to tell if you have a broken spring in your Wayne Dalton Torquemaster tube is if the door goes up and won't go back down.

Garage Door Repair Free Estimate Near Me Centennial Colorado


Sometimes, people unplug their power source and then wonder why their garage door opener fails to work. Sounds ridiculous, I know, but it does happen. Make sure that your garage door opener is plugged into a working outlet. Outlets sometimes go out without warning, so you can check to see if the outlet is working by plugging another working electronic device into it. Also, check your circuit breaker, fuse, or GFCI.

10.4 Raise the second bar 90 degrees and insert the first bar. This is "three." Continue winding. If the spring shortens in length, unwind the spring and switch sides - the springs are on backward. Otherwise, continue winding until you reach a count of "30." This is 7 1/2 turns, which is normal for most 7' doors. Longer life springs are wound the same number of turns. Newer steel doors with only one strut on top often need only 7 1/4 turns. On 8' doors count to 34. Each time you insert a bar into the winding cone, listen for the click to let you know the bar is in all the way. Not inserting the bar all the way could cause the cone to explode.

Garage Door Repair Guy Centennial Colorado 80016


6.4 Test the fit of the bar in the cone before loosening a set screw. Insert one end of your winding bar into one of the holes of the winding cone. Pull down on the bar slightly to make sure the set screws are tight. Position your ruler between the bar and the garage door. Move the bottom of the bar from side to side and measure the play. It should be less than an inch and a half. If it is over 2" either get someone else to change your springs or have someone make some bars that will properly fit the cones. https://www.youtube.com/watch?v=Z_eZc-kh40c&feature=youtube_gdata


Start your garage door spring replacement project by getting a rough measurement of your springs (length and diameter). Then measure the width and height of your door. Make sure the quote includes the trip charge, parts and labor. Then ask for a price based on 7x19 lift cables and double-life springs. Those items will give you more years of service and should only add $65 to the price.
For a scholarly introduction to torsion springs and for more information on how to install them I recommend you visit Richard Kinch's page, "How I Replaced Deadly Garage Door Torsion Springs and Lived to Tell the Tale." Richard is a brilliant engineer who has provided a wealth of technical information on fixing torsion springs along with valuable advice regarding some of the schemes unscrupulous garage door companies use to rip people off.
If your garage door's spring breaks, stops working properly, or snaps, you'll lose the ability to open and close your garage door. This could happen due to a variety of issues, like normal wear and tear or from extreme temperature changes in a short amount of time. Spring replacements require a quick response from a garage door provider near you. Contact The Home Depot and a local, background-checked technician will respond within 24 hours.

10.3 At this point you will wind the spring. Notice that the end of the spring on the winding cone points up when facing you. You will wind both springs up and counter intuitively as if you are trying to unscrew the winding cones from the ends of the springs. Begin by turning the spring up 1/4 turn until it meets resistance. This is your first quarter turn. Count "one." Next, insert the bar and raise it 90 degrees. Insert the second bar. This is "two." As you wind the spring it should grow in length the thickness of one coil for every turn. The cone should cover your mark after the first couple turns. Many garage door tradesmen mark the torsion springs with chalk or paint, but this often generates confusion.
Before we help you diagnose your stuck garage door, safety concerns can't be over stated. When trying to figure out how to fix a stuck garage door, it is important to take every safety precaution. Garage doors weigh hundreds of pounds and torsion springs hold a tremendous amount of energy waiting to be released, so without proper precaution it is possible to hurt yourself attempting to perform unauthorized repairs. 

Garage Door Repair Free Estimate Centennial Co


Remember, a garage door is usually made of metal and pushed along a metal track. That means that lubrication is essential, especially in winter. Keep in mind that lubrication can harden and get gunky as temperatures fall, so make sure that the lubrication on your tracks is rated for the lowest temperature that you’re likely to experience in your part of the world.
The track is secured with these little brackets and they're adjustable. There's a slot that it rides in so you can unscrew it here and adjust it if you need to. And you're going to have to pay attention and look at it closely to make sure it's in the right spot, but it's not that tricky and you can do it. And usually one side is out of alignment so you can compare it to the other and then adjust it as needed.
The Leading (scam) in the industry is the "LIFETIME WARRANTY". It sounds great when presented and seems fair and maybe even a good idea even though the initial cost seems pretty high (on average 450 - 700 dollars) what is not mentioned is the annual required cost (known as the required or annual door maintenance) to keep the warranty valid which if a standard 15,000 cycle spring/s is used should average Ten years, this annual service is usually 90 - 120 dollars. That would be another "900 - 1200" dollars invested in Ten years, that and the initial cost and you could buy two or more "complete new" doors in that time.
The Leading (scam) in the industry is the "LIFETIME WARRANTY". It sounds great when presented and seems fair and maybe even a good idea even though the initial cost seems pretty high (on average 450 - 700 dollars) what is not mentioned is the annual required cost (known as the required or annual door maintenance) to keep the warranty valid which if a standard 15,000 cycle spring/s is used should average Ten years, this annual service is usually 90 - 120 dollars. That would be another "900 - 1200" dollars invested in Ten years, that and the initial cost and you could buy two or more "complete new" doors in that time.
I purchased a garage door and opener and had HD install it. It was around $3600 and when the price increased by about $800 I called right away to pay it with no delay (these are all estimates written from memory). Anyway, I I bought the garage so that the front of the house would be prettier and it is but the old garage worked fine and I don’t even have a car in it so I don’t open and close it all and it actually only gets opened 2-3 times a month when a friend who stores their car there uses it. However, soon after the garage was installed, this friend told me the garage was working intermittently. When I called HD to come look at it, they said I would have to pay around $85 to have it looked at which didn’t make sense to me since it was brand new and almost immediately not working so it was likely a problem with the product or installation. HD would not provide immediate assistance to fix the problem, they insisted other steps which were unreasonable given it was a new garage and this request added great difficulty for me. Five months later after this back and forth calling to have someone from HD to just come and fix it, I went into the Huntington Beach store, spoke with Ryan who was polite and with little to say, he said I’ll put you on the list for an appointment and they will call in 24-48 to book a day and time. I was thankful. I also expressed my concern that I would not be charged for this visit and he said no unless it wasn’t covered under warranty. Two days later the installer called and said it will cost to around $95 just to show up. They arrived later that week, charged $95 and fixed the problem with no additional fee. If the garage was being used the way most garages are used and it was out of warranty, I could understand for a fee to cone out and look at it but because it stopped working almost Immediately and all the fuss and delay to have it fixed by HD was disappointing. When you gave me a quote then raised it by 20%% I paid immediately and without hesitation but this service was not reciprocated. I may have multiple projects at multiple sites but even if that weren’t the case, I would hope you would keep up your good costumer service history otherwise, your competitors willl slowly be better. Kindly return the fee charged for this service. Read less http://www.youtube.com/v/Z_eZc-kh40c&feature=share
Luckily, your garage door is a pretty sound investment. According to Garage Wow Now, garage doors were ranked in the top three for home improvements whose costs are recouped through increased home value. Similarly, realtors regularly increased the list price of a home with a new garage door by 1 to 4 percent! That means, if you spend $2000 on a new garage door, you can increase the value of your home by almost $8000 if you have a $200,000 home. Furthermore, compared with the other two highest rated improvements — siding replacement and deck installation — a garage door replacement is far more affordable.
Next, if you don’t find an obstruction, check the springs. If your door has torsion springs, which are horizontal at the top of the door, you can tell they are broken by checking for a gap between the two springs. If your door has extension springs, you can check by looking to see if they are hanging on the side of the door. If you have a broken spring, you’ll need to call a pro to replace it as this is a dangerous task.

Garage Door Repair Installation Centennial Co 80016


Insulation, which increases energy efficiency and can help to lower utility bills, is crucial when a garage door is attached to the home. In this case, doors with high R-values are preferred. This means it has insulation that can keep the heat in. The higher the R-value, the better insulated your garage will be against outside noise and cold and hot air.
If you have decided to replace your springs, if you are sure your door had the correct springs, and if you are ready to buy new ones, we recommend that you measure your spring or springs following the instructions in Step 4 below. Measuring springs can be difficult; most individuals, even garage door technicians, sometimes have difficulty measuring torsion springs. Ordering incorrect springs wastes time and money.
Your door’s torsion spring is located approximately one foot from the top section of your door when it is closed. It consists of two large coil springs, and is approximately the length of your arm. Its purpose is to balance the weight of your door so that a door weighing between 160 and 185 pounds is practically weightless to lift. As such, it makes it possible for a garage door opener to raise the door using only ten pounds of pressure.

Garage Door Repair Cost Centennial Co 80015


When you know you’re in range and the door still won’t open, check to make sure the antenna is hanging down from the motor inside your garage and nothing is blocking it. Your antenna must be free from any obstruction to clearly receive the signal to open and close the door. Also inspect the antenna for any signs of damage. If it looks like there has been damage to the antenna, you’ll need to call your garage door technician to come out and replace it.


Locating a contractor - there are many professional overhead garage door companies. It is always advisable to contact at least three different agencies and request a bid or quote for the work. Be sure that each quote includes the costs for a few different types of doors, any installation fees, and the cost of wiring the electronic openers. Standard prices range from: http://youtube.com/watch?feature=player_embedded&v=Z_eZc-kh40c
While a sudden issue is usually easily repaired, a consistent issue that has gone unaddressed for months or years will likely require a total replacement. The problem is that garage doors have a number of heavy, powerful moving parts. If the door is working as it is designed, it can open and close hundreds and hundreds of times without issues. However, if there is even a small issue in the lifting mechanism that repeatedly influences the movement of the door, you will soon find that the damage caused over those hundreds of lifts can’t be fixed.

Garage Door Repair And Service Centennial Co 80016


Like any mechanical part, garage door springs deteriorate due to normal wear and tear. Over time, the steel that makes up the springs weakens until they eventually break. Under normal circumstances, garage door springs have a life expectancy of 10,000 cycles of opening and closing. This equates to five to seven years, but along the way, there may be signs of problems that can occur before the springs actually stop working.

Garage Door Repair Guy Centennial Co 80015


Order replacement springs. Many manufacturers and distributors only provide torsion springs to professionals, and won’t sell them directly to the customer. Luckily, they are available on the Internet, so search online to find replacement springs. Make sure they match the coil size, length, and interior diameter of the springs you removed. Also, be sure to order both a “left-hand” and a “right-hand” spring as the coils are wound in different directions.[8]
×