Nate was very courteous and professional and called to let me know that he was about 30 minutes from my house. I had purchased a new Sears garage door opener, but when Nate arrived at my home, he inspected the existing unit and told me that it was still in good shape except for a worn out part. Nate procured the new part and brought it to my home this morning. The unit was repaired in about 10 minutes! The existing unit was just over five years old, so I'm glad I will get some more use out of it. http://youtube.com/v/Z_eZc-kh40c?version=3
The new opener was installed yesterday and today for a while it wouldn't close properly. The customer service representative said they will probably have to reverse the sensors. However, no one could come out today (Friday) or tomorrow. She will call me by Tuesday of next week to schedule someone to come here. The customer service rep. and the technician were nice but as of now, my new garage opener is not working to my satisfaction.
Insulation, which increases energy efficiency and can help to lower utility bills, is crucial when a garage door is attached to the home. In this case, doors with high R-values are preferred. This means it has insulation that can keep the heat in. The higher the R-value, the better insulated your garage will be against outside noise and cold and hot air.

Once the springs break, quite a bit of tension is put on the door cables, and they will often break next. When these cables break, they will snap and forcibly fly out like a broken rubber band. Think about how much it hurts to be snapped by a broken rubber band, and then multiply it by a hundred to account for the size and weight of the garage door cables.
If your garage door isn’t operating properly, the torsion springs are likely to blame. If you’re concerned about tackling this project on your own, consider hiring out the job to a professional. Otherwise, replace both the left and right springs at the same time to save yourself from having to do the job twice. Remove the old springs and measure them while they’re relaxed. Only then will you be able to order replacement parts and install the new springs. Replacing your own garage door springs takes only a little time and effort and can save you hundreds of dollars. 

If you've installed a replacement door or two around your home, it seems pretty simple -- all it takes is tightening a couple of screws and you're done. Installing t­he largest door in your house, however, is not quite so simple. Garage door in­stallation, whether manual or automatic, can be difficult and dangerous. Manual garage door installation is much easier than automatic garage door installation, but the one you choose generally depends on what kind of door you have.
On our EZ-Set Torsion Springs page you will find several options for replacing these springs. We also have step by step instructions for EZ-Set Torsion Spring Replacement. In addition, one of our customers has provided excellent EZ-Set Torsion System instructions for removing the spring without wrecking the winding unit that secures the stationary cone. Instead of a spanner tool, you may prefer to use a pipe wrench or large channel locks to hook the end of the spring and remove it from the cones in the last step.

Garage Door Repair Estimates Centennial 80015


Garage door springs don’t require extensive care and maintenance. However, they also can’t be left entirely to their own devices. Spraying the springs with WD-40 is a good place to start. It’s also a good idea to check the balance of the garage door every year. To do this, simply lift the garage door up about halfway and let go. If the springs are in good working condition, the door should remain still. If the springs are beginning to weaken, the door might sag or fall. By taking these basic steps, you can preserve your door springs for longer.
The Leading (scam) in the industry is the "LIFETIME WARRANTY". It sounds great when presented and seems fair and maybe even a good idea even though the initial cost seems pretty high (on average 450 - 700 dollars) what is not mentioned is the annual required cost (known as the required or annual door maintenance) to keep the warranty valid which if a standard 15,000 cycle spring/s is used should average Ten years, this annual service is usually 90 - 120 dollars. That would be another "900 - 1200" dollars invested in Ten years, that and the initial cost and you could buy two or more "complete new" doors in that time.
The two main garage door operating mechanisms are sectional roll-ups or tilt-ups. Garage door repair services can fix single-car, double-car or RV-height doors. Your garage door may be made of wood, steel, aluminum, masonite, vinyl, fiberglass or another material. The type of garage door repair you need really depends on the type of garage door you have and the issue at hand. Garage door repair pros often charge a flat service call fee to diagnose the problem and provide an estimate. For customers who choose to have the repair done, the service call fee may be applied to the first hour of labor (including time to make the diagnosis). If your garage door is under warranty, the repair may be free of charge.
77002, 77003, 77004, 77005, 77006, 77007, 77008, 77009, 77010, 77011, 77012, 77013, 77014, 77015, 77016, 77017, 77018, 77019, 77020, 77021, 77022, 77023, 77024, 77029, 77025, 77026, 77027, 77028, 77030, 77031, 77032, 77033, 77034, 77035, 77036, 77037, 77038, 77039, 77040, 77041, 77042, 77043, 77044, 77045, 77046, 77047, 77048, 77049, 77050, 77051, 77053, 77054, 77055, 77056, 77057, 77058, 77059, 77060, 77061, 77062, 77063, 77064, 77065, 77066, 77067, 77068, 77069, 77070, 77071, 77072, 77073, 77074, 77075, 77076, 77077, 77078, 77079, 77080, 77081, 77082, 77083, 77084, 77085, 77086, 77087, 77088, 77089, 77090, 77091, 77092, 77093, 77094, 77095, 77096, 77098, 77099, 77201, 77339, 77345, 77357, 77365, 77373, 77375, 77377, 77379, 77380, 77381, 77382, 77384, 77385, 77386, 77388, 77389, 77396, 77401, 77406, 77407, 77423, 77429, 77433, 77441, 77447, 77449, 77450, 77459, 77466, 77469, 77471, 77476, 77477, 77478, 77479, 77484, 77489, 77492, 77493, 77494, 77498, 77545, 77578, 77581, 77584, 77587,
Unlike torsion springs, replacing extension springs has long been given the "green light" for DIYers, primarily because you can complete the job without having to deal with spring tension. The general process is simple and safe: open the door to relieve the spring tension (and secure it open with C-clamps in the tracks); disconnect the spring from the track bracket and the spring pulley, and disconnect the safety cable from one end; install the new spring, reinstall the pulley, and reconnect the safety cable, and you're done.
In need of garage door repair? Contact one of our many well-trained garage door repair professionals today to provide your garage door system with the recommended service and maintenance procedures for smooth and reliable operation. Our garage door repair professionals are here for you, whether you want to fix your existing garage door or buy a new garage door. Are you looking to replace a garage door spring, cable or roller or searching for 'garage door repair near me'? Use our distributor locator below: 
When one or both springs break, gravity takes over and you feel the full weight of the door when lifting or lowering it.  It may be possible to pull the door up by hand, although doing so will likely be very difficult. In most cases, two or more people are needed to raise the door high enough for you to drive your car out of the garage. While single garage doors can typically be lifted, double doors are nearly impossible to manipulate due to their excessive weight. http://www.youtube.com/watch?feature=youtu.be&v=Z_eZc-kh40c

NEVER use screwdrivers, pin punches or pliers handles to wind or unwind a torsion spring. Trust us: This is the best way to wind up in the hospital. Don't even think about doing this job without a proper set of winding bars. You can buy a set of professional hardened-steel winding bars for about $25 from online suppliers. (Garagedoorpartsusa.com and stardoorparts.com are two online sources that sell winding bars, springs and other parts.) Professional winding bars work with 1/2-in. and 7/16-in. winding cones. If your winding cones have 1/2-in. openings, you can make your own winding bars by cutting a 36-in. length of 1/2-in.-diameter round bar stock in half (buy round bar stock from any hardware or home center). Just file a smooth bevel on each end so it slides into the winding cone holes easier.
However, if you are confident that you don’t just need new batteries, make sure to call a professional. A service person with a lot of experience will be able to look at the problem and quickly diagnose the issue, saving you precious time. Again, while you may be able to save money in the short term by taking a day off and troubleshooting the problem yourself, the amount of energy and time lost as you search out the issue will quickly surpass the cost of a professional repair. https://www.youtube.com/v/Z_eZc-kh40c&feature=kp
Eric Jonas has been writing in small-business advertising and local community newsletters since 1998. Prior to his writing career, he became a licensed level II gas technician and continues to work in the field, also authoring educational newsletters for others in the business. Jonas is currently a graduate student with a Bachelor of Arts in English and rhetoric from McMaster University.
The new opener was installed yesterday and today for a while it wouldn't close properly. The customer service representative said they will probably have to reverse the sensors. However, no one could come out today (Friday) or tomorrow. She will call me by Tuesday of next week to schedule someone to come here. The customer service rep. and the technician were nice but as of now, my new garage opener is not working to my satisfaction.

Garage Door Repair Free Estimate Centennial 80016


Using your drill, add tension to the torsion spring. This system uses a single spring for a double door, but many manufacturers use two springs for a double door. The painted line on the spring acts as a gauge for the number of turns you put on the spring. To keep the bar from turning while you’re adding tension, attach a locking pliers to the bar on both ends of the spring. Apply lubricant for garage doors to the spring.

With Sears Garage Doors you can feel confident that you are getting the very best for your home and your family. All of our technicians are background checked, professional, and committed to complete customer satisfaction. The "best" is standard for all new Sears Garage Doors, Sears Garage Door Openers and Sears Garage Door Repairs. We offer some of the best warranties available in the industry, the best design advisors, the best technicians, and the best products. We may be a little biased, but we also believe we have the best customers. Go ahead, choose to be part of the best.

Garage Door Repair And Service Centennial 80016


If the door only goes up six inches and stops, or moves very slowly when using your remote, you could have a broken spring as well. Some customers will notice that the top section of their door is bent or that the door falls very quickly when lowering. Your door may be “crooked” or jerky when going up and down, and both of these signs indicate your torsion spring is in poor condition and very likely to break in the near future. Any time you hear a loud “popping” noise while operating, you should inspect your torsion spring immediately for signs of damage.
You can reschedule or cancel your service at any time. To reschedule, simply go to Your Orders, find your service order and click on the ‘Contact Provider’ button on Your Orders page. To cancel, click on the 'Cancel Order' button on Your Orders page. Payment goes to the pro from your secure Amazon account. Because you aren't charged until the actual work is completed, cancelling a job doesn't require a refund.
The average cost is $190 for 2 springs in the Detroit area. This is for steel doors weighing under 140 lbs or known as a standard spring which fits 90% of all doors. The remaining 10% are wood doors or large heavy insulated doors. Expect to pay an additional $60 - $100 for a set of these. Garage Door Companies rarely carry these springs on their vehicles or stock them. Therefore, they either buy them locally at a premium or special order them. Regardless, its an additional trip that gets figured into the cost.
They were quick, friendly, and highly professional. Little things like making me enter security code from the other side of the closed garage door revealed their attention to security They had to run to Home Depot to get a small block of wood to fix an existing problem with the door — They didn’t charge me extra. Quite unexpected & appreciated. 10 out of 10
Roberto was very courteous and explained the details of what he was doing. He also pointed out a repair I might consider having done (replacement of the bottom panel of my door) and asked the office to follow up with me on this. Someone did follow up with me and since replacement of the bottom panel is not an option and I would have to replace the door, I decided that I can wait.
My experience with Overhead Garage Door was exceptional! They were friendly and fast! I didn’t have to wait days to hear back from them and their prices were far better than that of their competitors top article. I would highly recommend Overhead Garage Door to anyone needing assistance with their door and especially if you’re in the market for a new one!
We are proud of the work we do in Northwestern North Carolina. We love this community and we love serving it. So whether you think you need a small repair or a major overhaul, we want to be the team that helps you increase the value of your home while making it a safer place to live for you and your family. Our professional and friendly sales team are eager to connect with you, so contact us today and find out just how we can ease your concerns and make transform your garage! http://m.youtube.com/e/Z_eZc-kh40c
However, in addition to potentially causing injuries to the under-prepared DIYer, a malfunctioning door can become a safety hazard to you and your family. Keep in mind, according to the National Electronic Injury Surveillance System (NEISS), over 13000 people checked into hospitals with garage related injuries in the United States in 2007. You don’t want to turn a loved one into a statistic just to save a few dollars! 

Automatic Garage Door Repair Centennial Co 80015


Unlike torsion springs, replacing extension springs has long been given the "green light" for DIYers, primarily because you can complete the job without having to deal with spring tension. The general process is simple and safe: open the door to relieve the spring tension (and secure it open with C-clamps in the tracks); disconnect the spring from the track bracket and the spring pulley, and disconnect the safety cable from one end; install the new spring, reinstall the pulley, and reconnect the safety cable, and you're done. http://www.youtube.com/watch?feature=youtube.be&v=Z_eZc-kh40c
The problem is that one of the garage doors "catches" (i.e. stops) while going up at about 2 feet off the ground ~90% of the time. When the button is pressed again, it goes all the way down. This cycle can be repeated ad nauseum, or I can give the door a gentle tug upward just before the "Sticking" point, and this will give the door enough "impetus" to make it all the way up.
Slide the left spring onto the tube and add the cable drum. When your new springs arrive, put the new left spring (the 1 with the end facing up and to the left) on the torsion tube, making sure that the stationary cone on the end of the spring faces the center bracket. After sliding the new spring into place, replace the cable drum and insert the torsion bar into the left bearing bracket.[9]
It is precisely on those coldest days of the year when you most need and appreciate the convenience of opening and closing your garage door quickly. Sadly, that's exactly the kind of day when moisture and cold can conspire to make this difficult. Garage doors can and do freeze to the garage floor. Sometimes it is just a minor icy connection between the two that can be broken when you hit the opener button. If the door refuses to budge on the first attempt, though, resist the urge to keep banging on the automatic opener button. This is likely to cause a more serious problem with the garage door opener—including, but not limited to, stripped gears, broken springs, and a burned-out motor on the opener.
On average, to have your springs replaced on your garage door will vary anywhere from $200 to as much as $400 if you were to hire a professional.  Breaking the costs down, the springs, depending on the part needed and the size, will cost about $20 to $60 each.  Add in the labor, which can be $45 to $85 per hour, depending on your location, can bring the grand total to the estimate noted.   A tilt-up door, on average, will be about 20 to 30 percent less than a roll-up door.

Since most yards entertain play activity including baseballs and other sporting equipment, it's no surprise that garage doors experience broken glass from time to time. Regardless of the cause, it's important to repair glass quickly, since broken glass in a garage is a safety issue, a security problem, and an invitation to every bird and insect in the neighborhood to take up residence in your garage. Fortunately, it's not difficult to replace a pane of glass. The techniques are exactly the same as for replacing glazing in a house window.
In order to replace your garage door spring(s), you will need to find the current measurements in order to accurately replace the spring(s). This should take about 3 minutes and you don't need to remove the springs or loosen the tension to measure them. Our springs are made to be a bit flexible, so you don't have to get it to an exact measurement. 
Keep in mind, the pulley is often cycled through an enclosed casing that is difficult to lubricate directly. By applying enough lubricant to the pulley, you’re ensuring that the whole lifting mechanism is properly lubricated. Furthermore, a jam in this portion of the lifting mechanism is a time-consuming and potentially labor expensive repair that requires a service professional.
For a scholarly introduction to torsion springs and for more information on how to install them I recommend you visit Richard Kinch's page, "How I Replaced Deadly Garage Door Torsion Springs and Lived to Tell the Tale." Richard is a brilliant engineer who has provided a wealth of technical information on fixing torsion springs along with valuable advice regarding some of the schemes unscrupulous garage door companies use to rip people off.
Garage doors make life easier, particularly when you’re arriving home in the middle of a rainstorm. It’s easy to take the convenience a garage door provides for granted -- until it stops working properly. The door loses its visual appeal instantly, stuck there half-open. This type of situation also raises security concerns as a simple trip to the store can become a headache. Simple fixes when a garage door gets stuck halfway may prevent it from happening again.
I got these replacement cables for my beach house garage door after the originals rusted and broke. These are twice the diameter of the OEM cables, and fit the door perfectly. The larger cables give piece of mind for both supporting the door and providing safety cables for the extension springs. Came with all the necessary hardware, and the installation was easy with the doors blocked in the up position.
Overhead Door Company of Central Jersey has been in the garage door industry since 1972. Our proficient service technicians offers the best installation, maintenance and replacement for your garage doors and parts. You can check our our Before and After residential garage doors photos for reference. Kindly click on "Schedule at-home appointment" below to get started.
Everyone wants to save money. Unfortunately, there are some areas you just can’t skimp on. This includes garage door springs. As much as it might be tempting to by smaller or cheaper springs, or maybe to buy one spring where two are needed, these attempts to save money will only end up costing more money in the end. When you buy the proper springs, they’ll last for years. When you cut corners to save money, the springs will wear out faster, meaning they’ll need to be replaced much sooner.
Finally, one of the most important garage door innovations over the years in increased child safety features. Sensors can detect when a child or pet is crossing the threshold while the door is closing, prompting it to stop immediately. Furthermore, doors can also sense when something is being pressed by the door, causing it to stop before inflicting a brutal crushing injury.

Gather the supplies and tools needed for changing the springs safely. In addition to the torsion springs you'll need a minimum of one or two 10" vise grips, an adjustable wrench, and two 1/2" X 18" winding bars. Most hardware stores sell 1/2" X 36" steel rods that can be cut in half. You'll also need a firm ladder and a rag for cleaning your hands. A ruler and a file may also be necessary; a socket wrench and sockets would shorten the time required. Finally, make sure your garage is lighted well.
×