Delivered on time, with the products described: springs, winding bats, & plastic bushing. Quick install, but apparently I measured wrong, so these total length I bought was larger (which is good as there is less stress on the spring). However this did mean that I needed more than the generic rule of 30 1/4-turns of preload. I wound up with 38 1/4-turns per side for the door to balance when open 3' (per familyhandyman.com recommendations). Would definitely do it again.
7.3 Slide both torsion springs out above the top of the garage door toward the cable drums. Notice that there is only one bushing or bearing between the cones. Sometimes a single bearing is pressed into the bracket; other brackets have a single bearing or bushing that fits in either cone. Do not try to install a bushing or bearing in both of the stationary cones. You will risk breaking a cone. The purpose of the bushing is to keep the shaft from wearing against the spring anchor bracket. Only one bushing is needed to accomplish this.

Garage Door Repair Images Centennial Co


To install a single new garage door it should cost between $500 and $800. They demonstrate that the average homeowner can usually tackle such a project in a nine hour time span and a professional will be able to complete it in roughly five hours. Should it be a DIY project? Not really, most housing experts point out that it is a two-person job, requires advanced carpentry skills, and even knowledge of household electronic systems.
9.8 Twist the garage door shaft to tighten the cable on the drum. While twisting, vise grip the shaft as shown to keep the cable tight on the drum. The top of the vise grip should be tight against the garage header. This will keep the cable snug on the first drum while you install the cable on the other drum and position it in place. It also keeps the shaft from turning and the cables peeling off when you wind the springs. That one grip can save many hours of walking back and forth and having to level and re-level the garage door after winding the torsion springs.
Although you should let professionals perform any tasks that require adjusting the tension on the springs, there are a few repairs you can do and maintenance tasks that extend the life of the door. One such repair is to tighten the nuts and bolts that hold the garage door and its track together. This also provides an opportunity to check the door and its parts for signs of wear and damage. You can also lubricate all the moving parts in the door, including the pulleys, bearings and springs. This shields the parts from dirt and helps reduce noise when the door opens and closes. Another job you can complete is installing an automatic garage door opener.
6.10 If the garage door comes off the floor when you pull down on the bar, and if the cone still won't loosen, tap the bar next to the cone with a hammer to force the cone beyond the swollen portion of shaft. Maintain a firm grip on the bar; keep it firmly inserted completely into the cone; and be prepared at all times for the cone to slip, break, explode or break free from the shaft and yank the bar down.
Annual maintenance. Make an annual check of all nuts and bolts on rails and rollers to make sure they’re firmly tightened. Check the condition of all cables to make sure they’re not worn or frayed. Lubricate rollers and springs with a garage-door lubricant (see How to Fix a Noisy Garage Door for maintenance and problem-solving tips). The door should operate smoothly and be properly balanced. Check the balance by disconnecting the opener and lowering the door halfway- the door should hold its position. If it doesn’t, adjust the spring tension or replace the springs.
6.4 Test the fit of the bar in the cone before loosening a set screw. Insert one end of your winding bar into one of the holes of the winding cone. Pull down on the bar slightly to make sure the set screws are tight. Position your ruler between the bar and the garage door. Move the bottom of the bar from side to side and measure the play. It should be less than an inch and a half. If it is over 2" either get someone else to change your springs or have someone make some bars that will properly fit the cones.
7.3 Slide both torsion springs out above the top of the garage door toward the cable drums. Notice that there is only one bushing or bearing between the cones. Sometimes a single bearing is pressed into the bracket; other brackets have a single bearing or bushing that fits in either cone. Do not try to install a bushing or bearing in both of the stationary cones. You will risk breaking a cone. The purpose of the bushing is to keep the shaft from wearing against the spring anchor bracket. Only one bushing is needed to accomplish this.

Garage Door Repair Images Centennial Co


So if you’re worried that your door may be becoming more energy inefficient or if you’ve noticed a sudden spike in your heating costs, look at the weather stripping on your garage door. While you can replace it yourself, remember that effective weather stripping requires a tight seal, so if you’re unsure, you might save money in the long run by going with a professional garage door service 

Standard torsion springs (about $40 each) have a service life of 7,000 to 10,000 open/close cycles. However, you can buy double-life (25,000 cycles) replacement springs for about $65 per spring. If you have a two-spring setup and one spring breaks, the second spring will break soon. So replace them both at the same time. To get the right springs for your door, you'll have to provide the supplier some details. Here's how:


Delivered on time, with the products described: springs, winding bats, & plastic bushing. Quick install, but apparently I measured wrong, so these total length I bought was larger (which is good as there is less stress on the spring). However this did mean that I needed more than the generic rule of 30 1/4-turns of preload. I wound up with 38 1/4-turns per side for the door to balance when open 3' (per familyhandyman.com recommendations). Would definitely do it again.


Refrain from parking your car in the garage until the garage door is repaired. Additionally, try not to open and close the door while it’s in this condition. With that amount of possible force coming from the springs or cables, they could potentially damage your vehicle or other property in the garage as well as cause serious injury. It’s especially important that you and your family stay away from these cables or springs until everything is repaired.
Install the vertical roller tracks first by wrapping the curved lip around the rollers. The top of these tracks should be approximately 8 in. below the top of the top section. Wait to install the upper tracks until this step is complete. Check the level of the top section to make sure the tops of the vertical roller tracks are level with each other. The bottom of the roller tracks should be at least 1/8 in. off the concrete floor. After leveling and mounting these tracks, install the upper roller (horizontal) tracks.
With Sears Garage Doors you can feel confident that you are getting the very best for your home and your family. All of our technicians are background checked, professional, and committed to complete customer satisfaction. The "best" is standard for all new Sears Garage Doors, Sears Garage Door Openers and Sears Garage Door Repairs. We offer some of the best warranties available in the industry, the best design advisors, the best technicians, and the best products. We may be a little biased, but we also believe we have the best customers. Go ahead, choose to be part of the best.
Often companies will show different types of springs like oil dipped, galvanized or powder coated and try to convince you that one is longer life than the other and that is why it is going to cost this much instead of that much. Galvanized and Powder coated are great for coastal areas as a rust preventative but do not change the cycle life and do not cost but a few dollars more.
10.4 Raise the second bar 90 degrees and insert the first bar. This is "three." Continue winding. If the spring shortens in length, unwind the spring and switch sides - the springs are on backward. Otherwise, continue winding until you reach a count of "30." This is 7 1/2 turns, which is normal for most 7' doors. Longer life springs are wound the same number of turns. Newer steel doors with only one strut on top often need only 7 1/4 turns. On 8' doors count to 34. Each time you insert a bar into the winding cone, listen for the click to let you know the bar is in all the way. Not inserting the bar all the way could cause the cone to explode. https://m.youtu.be/Z_eZc-kh40c

In this article, we’ll tell you the difference between a safe door and one that’s unsafe. We’ll also give you the helpful tips you’re not likely to find in the manufacturer’s instructions to correctly, and safely, install a new garage door with a torsion spring and do-it-yourself tensioning. Installing a new, double garage door yourself will save you several hundred dollars and should take eight to 12 hours if you’re fairly handy. You can do most of the new garage door installation project yourself, but you should recruit help for removing the old door.

Garage doors eventually begin to break, look terrible and pose safety risks. How old is your garage door? Have you ever had a safety inspection performed? Garage door safety should always be a top priority as it could cause serious injuries and cost you the expense and trouble of personal injury lawsuits. Our blog will show you what you need to know about garage door safety inspections to assist you with the inspection and upgrades of your home's garage door. Hopefully, what we show you will help to keep your friends and family safe from harm when they visit you.

Garage Door Repair Near Me Centennial Colorado 80015


2. These springs do wear out over time – in fact, they are commonly rated with what is called a cycle life. The average standard cycle life is ten thousand cycles with each cycle being one opening and closing of the door. This means for a door that sees four cycles per day you might expect to replace your springs after somewhere close to seven years of use.
There’s another reason new doors are superior to old ones: energy efficiency. Keep in mind, garage doors are large, and when they open, they let a lot of outside air into your home. While you may have significant insulation separating your garage from the rest of your home, eventually that temperature differential will start to influence your energy bills.
Overhead Garage Door was prompt in keeping the appointment, efficient in their work and professional when they worked on my garage door. The garage door was broken and the technician couldn’t have been nicer or quicker in getting the door repaired. I don’t know when I’ve had such good service from anyone! To add to that already wonderful service, I then received a follow up from the owner asking me about my experience and to make sure my door was working well. I highly recommend Overhead Garage Door for all of your garage door needs.

Garage Door Repair Cost Centennial 80016


The average cost is $190 for 2 springs in the Detroit area. This is for steel doors weighing under 140 lbs or known as a standard spring which fits 90% of all doors. The remaining 10% are wood doors or large heavy insulated doors. Expect to pay an additional $60 - $100 for a set of these. Garage Door Companies rarely carry these springs on their vehicles or stock them. Therefore, they either buy them locally at a premium or special order them. Regardless, its an additional trip that gets figured into the cost.
Unlike torsion springs, replacing extension springs has long been given the "green light" for DIYers, primarily because you can complete the job without having to deal with spring tension. The general process is simple and safe: open the door to relieve the spring tension (and secure it open with C-clamps in the tracks); disconnect the spring from the track bracket and the spring pulley, and disconnect the safety cable from one end; install the new spring, reinstall the pulley, and reconnect the safety cable, and you're done.

They were quick, friendly, and highly professional. Little things like making me enter security code from the other side of the closed garage door revealed their attention to security They had to run to Home Depot to get a small block of wood to fix an existing problem with the door — They didn’t charge me extra. Quite unexpected & appreciated. 10 out of 10

Garage Door Repair And Service Centennial Colorado 80016


It’s difficult to say how often the springs will need to be replaced since it’s different for everyone. It depends on how often you use your garage door, how cold and long your winters are, how well you maintain your springs and many other factors. The best rule of the thumb is to check your springs regularly for signs of wear and damage and to replace them when they begin to appear tired.
If the sensors are malfunctioning, it can cause the garage door to get stuck. One of the sensor lights will typically begin blinking if they aren’t working properly. The first thing to check for is an obstruction in the path of your garage door. If the doorway is clear, then check to see if the sensors are properly aligned. If they are out of alignment, then they can’t see one another and their line of vision is broken. Re-aligning them should result the garage door becoming unstuck if this is the case.

Homeowners have long been warned that torsion springs are extremely dangerous to work with and that replacing them must be left to a professional. But these claims are somewhat exaggerated. If you understand how they work, and you pay attention to what you're doing, you can replace them safely and surprisingly easily. Granted, they're a little spooky to work with at first (partly due to their reputation), but this is a good thing—you really don't want to forget that they're under tension. Thinking about every step — before you take it — is the key to staying safe. http://m.youtu.be/Z_eZc-kh40c
On our EZ-Set Torsion Springs page you will find several options for replacing these springs. We also have step by step instructions for EZ-Set Torsion Spring Replacement. In addition, one of our customers has provided excellent EZ-Set Torsion System instructions for removing the spring without wrecking the winding unit that secures the stationary cone. Instead of a spanner tool, you may prefer to use a pipe wrench or large channel locks to hook the end of the spring and remove it from the cones in the last step.

Garage Door Repair Estimates Centennial 80015


When I called to schedule the repair service, I was transferrd 5 times and spoke with 6 service reps. Each rep was very confused by my request to get my garage door repaired. One rep actually told me that Sears doesn't repair garage doors. I had to tell her that Sears installed the door. When I finally found a rep who could schedule my service, it took one week for the appointment.
We want to hear from you and encourage a lively discussion among our users. Please help us keep our site clean and safe by following our posting guidelines, and avoid disclosing personal or sensitive information such as bank account or phone numbers. Any comments posted under NerdWallet's official account are not reviewed or endorsed by representatives of financial institutions affiliated with the reviewed products, unless explicitly stated otherwise.
×