Your door’s torsion spring is located approximately one foot from the top section of your door when it is closed. It consists of two large coil springs, and is approximately the length of your arm. Its purpose is to balance the weight of your door so that a door weighing between 160 and 185 pounds is practically weightless to lift. As such, it makes it possible for a garage door opener to raise the door using only ten pounds of pressure.

Garage Door Repair Cost Centennial Co 80015


Garage doors eventually begin to break, look terrible and pose safety risks. How old is your garage door? Have you ever had a safety inspection performed? Garage door safety should always be a top priority as it could cause serious injuries and cost you the expense and trouble of personal injury lawsuits. Our blog will show you what you need to know about garage door safety inspections to assist you with the inspection and upgrades of your home's garage door. Hopefully, what we show you will help to keep your friends and family safe from harm when they visit you.
Copyright © 2019 HubPages Inc. and respective owners. Other product and company names shown may be trademarks of their respective owners. HubPages® is a registered Service Mark of HubPages, Inc. HubPages and Hubbers (authors) may earn revenue on this page based on affiliate relationships and advertisements with partners including Amazon, Google, and others.
2.3 Beware of older winding cones. These older Crawford and McKee torsion spring cones were made for 5/8" bars. Sometimes, however, the holes are too small for 5/8" bars. Whatever you do, don't use a 1/2" bar; instead, grind down a 5/8" bar to fit. I recently had a McKee spring let loose after winding because I used a 1/2" bar when my 5/8" bar wouldn't fit. Just before it let loose I was telling myself, "This is not safe." And it wasn't. The only safe way to replace these older springs is to make a winding bar for each hole of each cone.
Garage Door Spring, garage door houston, garage doors houston, houston garage door repair, garage door opener houston, garage door installation houston, garage door openers houston, garage door service houston, garage doors in houston, garage door repair in houston, garage door services houston texas tx, garage door torsion springs, Emergency Garage Door Repair

Garage Door Repair Free Quote Centennial Colorado 80015


Homeowners have long been warned that torsion springs are extremely dangerous to work with and that replacing them must be left to a professional. But these claims are somewhat exaggerated. If you understand how they work, and you pay attention to what you're doing, you can replace them safely and surprisingly easily. Granted, they're a little spooky to work with at first (partly due to their reputation), but this is a good thing—you really don't want to forget that they're under tension. Thinking about every step — before you take it — is the key to staying safe.

Garage Door Repair Images Centennial Colorado 80016


He is required to call in a service report for approval to repair, he reported the old springs and the broken door opener, obviously not well maintained (although installed in 1980 and operated until 2018) so the service company denied the claim and the service tech left with $125.00 just for showing up. The service company will no longer cover the door opener.
If the garage door is broken or damaged, it can affect the feeling of the entire house. It’s not only an inconvenience, but it can also make your entire house feel less sophisticated and less functional. If you happen to be trying to sell your house, this can seem like a major detraction. Even if you’re only having guests over, you may feel as though you’re doing less than putting your best foot forward by having a broken garage door.

The following procedures are based on my 30 years in the garage door industry. In spite of my high mechanical aptitude, even after 18 years in the trade I lost the end of my left index finger. A few years later I had five stitches in my right thumb, and a year later five stitches in my left thumb. In 2004 emergency room staffs dug steel out of my eye and sewed up my ring finger with eight stitches. The best I can do is help you minimize the risk of injury; that's all I can do for myself. I am not so naive as to think that I have made my last trip to the emergency room. Repairing garage doors, particularly replacing torsion springs, is dangerous work, whether you are a do-it-yourself homeowner or an experienced technician.

If you have a garage door opener and you suspect a spring has broken, do not disconnect the opener from the door (by pulling the red emergency release handle) while the door is open. If you do, the door can come crashing down under its nearly full weight, with nothing to stop it. This is an extremely dangerous situation. It is never safe to leave the door open when a spring has broken because someone might try to close the door without realizing how heavy it is. Or, they might pull the emergency release handle on the opener.
Finally, we also carry any and every residential garage door product that you need to have a state-of-the-art, secure and safe garage door. We are proud certified dealers of Clopay doors, the most durable and versatile doors on the market. With over fifty years of garage door manufacturing experience, you can trust Clopay quality, just as you can trust our team to install these highest-quality doors.

Grab a tape measure and press the hook between two spring coils and note the length of 20 coils. Then measure 40 coils. Convert the measurements to a decimal (4-1/2 in. to 4.5 in., or 4-1/8 to 4.125, for example). Divide the two measurements by 20 and 40 to obtain the spring's wire diameter. Here's an example: 4.50 divided by 20 = .225-in. wire diameter; 9.0 divided by 40 = .225-in. wire diameter. If the two results match, you've measured correctly. http://m.youtube.com/watch?v=Z_eZc-kh40c

When you install a new garage door, replace all the hardware as well. If your automatic opener doesn’t have an automatic reversing system that includes photoelectric eyes, replace it. Doors with openers also require two extra pieces of hardware that you’ll see in Photo 4: a support strut (usually included in the door kit) and an opener bracket (not included). For doors with torsion springs located over the door, spend the $50 or so to have a garage door professional release the tension.


10.4 Raise the second bar 90 degrees and insert the first bar. This is "three." Continue winding. If the spring shortens in length, unwind the spring and switch sides - the springs are on backward. Otherwise, continue winding until you reach a count of "30." This is 7 1/2 turns, which is normal for most 7' doors. Longer life springs are wound the same number of turns. Newer steel doors with only one strut on top often need only 7 1/4 turns. On 8' doors count to 34. Each time you insert a bar into the winding cone, listen for the click to let you know the bar is in all the way. Not inserting the bar all the way could cause the cone to explode.
	6.8 Properly tightened screws will loosen with less than a turn. Once you loosen a set screw, keep at least one bar in the cone AT ALL TIMES until the spring is fully unwound. Many cones have been over-tightened. The spring may unwind 1/4 turn and not unwind any more until one of the set screws is loosened some more. You may need to completely remove the set screws. The shaft may be distorted and the cone still may not unwind at all.

If the garage door is broken or damaged, it can affect the feeling of the entire house. It’s not only an inconvenience, but it can also make your entire house feel less sophisticated and less functional. If you happen to be trying to sell your house, this can seem like a major detraction. Even if you’re only having guests over, you may feel as though you’re doing less than putting your best foot forward by having a broken garage door. http://www.youtube.com/watch?v=Z_eZc-kh40c&app=desktop
7.2 If the spring bracket is slotted, vise grip the bracket to secure the shaft in the bracket. This will keep the shaft from possibly falling out and causing injury or damaging the garage door or shaft. You can also secure the shaft with a cable tie. Remove the bushing from the cone and leave it on the shaft next to the center spring bracket. Often the bushing gets stuck in the cone and customers will call us about getting a new bushing until they discover it is still in the cone of the spring replaced earlier.
Does your garage door stop when it is going up? Did you hear a loud bang, similar to a gun shot? Do the torsion springs above your door seem separated? If so, you might just have a broken torsion garage door spring. Torsion springs are located above the garage door and they are what lift the actual weight of the garage door. Most doors weigh between 150 to 250 pounds and without working springs, the garage door opener cannot lift the door. Attempting to use a garage door opener to lift a garage door with a broken spring can cause numerous parts on the opener to break.
Center and level the first section after you install the brackets. The door must be level even if the floor isn’t, so use shims under the section to level it. The rubber gasket on the bottom section will fill the gaps created by an unlevel floor. To hold the level in place, tape it to the section. To hold the section in place, lightly toenail a 16d nail into the frame and bend it over the section. Add brackets and rollers before setting them in place and stack one section on top of another, toenailing as you go up.
×