When a garage door service company gets a phone call in reference to a broken spring, the first thing the homeowner usually says is “the cables are broken”. This makes sense because the cables on a garage door will fly every which way, fall to the ground, become disconnected from the door, or even get caught in between the garage door and the jamb. It is rare for cables to break or need replacing when a garage door spring breaks. If your garage door has two torsion springs, the second spring will keep the cables tight and on the drums. You will have to look up at the springs to determine if one is broken.
9.14 Slide the springs to the bracket. Double-check to make sure you have the right wound spring on the left side and the left wind spring on the right side. Turn the springs until the ends are facing you. The wire at the ends of both torsion springs here at the bracket should be pointing down. At the winding cones at the opposite ends, the spring wire points up. If not, reverse the springs. About once a month we get a phone call from a do-it-yourself customer who begins the conversation with, "I wound the garage door spring to about six turns and the spring came loose from the cone." We normally refer them back to this step and suggest they switch their springs.

Garage Door Repair Free Quote Centennial Colorado


For Sears Garage Door Installation and Repair Services, making your garage door safe is as important as making it function well. For this reason, all of our repair services and tune-ups feature a 20-point safety check. Our technician will carefully examine your garage door panels, springs, sensors, safety release, hardware, track, and more. This ensures that, not only has our work been done well, but that your garage door poses no danger to your vehicles or family. Due to the intricacy of garage door systems, only garage service professionals should attempt to adjust, repair, or service door equipment.
If the track is misaligned, but the door still moves, there are a few things you can do to attempt to remedy the issue on your own. You’ll know that it’s misaligned if you hear a rubbing noise when the garage door reaches a certain spot on the tracks each time it opens and closes. Sometimes the door may even slow down slightly when it hits this spot.
My garage door torsion spring broke so I decided to replace it myself. Shipping was next day. I got the torsion spring rod at a local hardware store. Easy to install once I figure out how to lock down the rod from moving and loosening the door cable on the side. Instructions tells you how to do it. Great replacement spring and save $$$ doing it myself. https://m.youtube.com/watch?v=Z_eZc-kh40c
If the engine of your garage door opener isn’t working properly, then your garage door probably won’t be working properly. If your garage door gets stuck and you hear a grinding sound coming from the garage door opener, then there’s a good chance that there is an issue with its engine. That issue is that the main drive gear probably needs to be replaced. The main drive gear is most common of the garage door opener’s components to fail. It is a plastic gear that takes some know-how to remove and replace, which is why you should strongly consider hiring a professional garage door repair service for this particular issue. http://youtube.com/v/Z_eZc-kh40c
Our garage door broke 3 days before Christmas, trapping my car inside. We contacted our home warranty, and within 24 hours, Sears called with an appointment time for the next day! I was so impressed! I thought, for sure, with the holidays, we would have to wait. When the technician showed up, he was so friendly. Unfortunately, the repair was not covered under our warranty, but he was able to help us get a good deal on a new spring and still make the repairs that day before he left. He also gave us great advice on how to keep the spring lubricated so it would not break again. I felt like he really went above and beyond to provide great service. Since moving into this new house in August, we have used Sears for several things now, and have been very pleased with the service. It's nice to see that in an age when so many companies just put customer service on the back burner in order to meet their bottom line, Sears still really cares and makes their customers feel important. Thanks for taking care of us this Christmas!

Annual maintenance. Make an annual check of all nuts and bolts on rails and rollers to make sure they’re firmly tightened. Check the condition of all cables to make sure they’re not worn or frayed. Lubricate rollers and springs with a garage-door lubricant (see How to Fix a Noisy Garage Door for maintenance and problem-solving tips). The door should operate smoothly and be properly balanced. Check the balance by disconnecting the opener and lowering the door halfway- the door should hold its position. If it doesn’t, adjust the spring tension or replace the springs.
Both types of springs are _loaded_, or under tension, when the door is closed. This gives them stored energy to help lift the door as it's being opened. When the door is all the way up, the springs are relaxed, or relatively so—they still may be under some tension. The mechanical difference between extension and torsion springs is that extension springs are loaded by stretching, or elongating, while torsion springs are loaded by twisting, creating torque.
The garage door opens and closes many times throughout the year, and something may blow inside. While it is usually something such as loose leaves or small amounts of dirt, the rails that the door travel along can collect this loose debris. Over time, the buildup of debris creates a blockage on the rails. Note where on the rails the door is stuck and clean that area. If children use the garage to leave the house, it's sometimes something as simple as a small, bouncing ball that happens to land in just the right -- or wrong -- spot.
With Garage Door Doctor, you can rest assured we will replace your springs correctly. We offer 2 types of springs – standard and high cycle. On a 7 foot tall door, our standard torsion springs will last 15,000 cycles and our high cycle torsion springs will last 50,000 cycles. How many years will this last you? That is based off only one thing – usage. For example, with standard torsion spring, if you use your door 4 times a day, you get just over 10 years of life. However, if you use your door 8 times a day, you would get just over 5 years of life. If you use door very little or if you are moving very soon, maybe standard springs would be best for you. If you use your door many times a day or if you don’t plan on moving for a while, high cycle springs would be best for you. Getting high cycle springs will ensure you won’t be stuck with a broken spring for many years to come. Either way, both types of torsion springs we offer work great – its just a matter of when the break again. Call Garage Door Doctor today to have your garage fixed properly!
While a sudden issue is usually easily repaired, a consistent issue that has gone unaddressed for months or years will likely require a total replacement. The problem is that garage doors have a number of heavy, powerful moving parts. If the door is working as it is designed, it can open and close hundreds and hundreds of times without issues. However, if there is even a small issue in the lifting mechanism that repeatedly influences the movement of the door, you will soon find that the damage caused over those hundreds of lifts can’t be fixed.

Garage Door Repair Images Centennial 80016


If the engine of your garage door opener isn’t working properly, then your garage door probably won’t be working properly. If your garage door gets stuck and you hear a grinding sound coming from the garage door opener, then there’s a good chance that there is an issue with its engine. That issue is that the main drive gear probably needs to be replaced. The main drive gear is most common of the garage door opener’s components to fail. It is a plastic gear that takes some know-how to remove and replace, which is why you should strongly consider hiring a professional garage door repair service for this particular issue. http://youtube.com/v/Z_eZc-kh40c
While a sudden issue is usually easily repaired, a consistent issue that has gone unaddressed for months or years will likely require a total replacement. The problem is that garage doors have a number of heavy, powerful moving parts. If the door is working as it is designed, it can open and close hundreds and hundreds of times without issues. However, if there is even a small issue in the lifting mechanism that repeatedly influences the movement of the door, you will soon find that the damage caused over those hundreds of lifts can’t be fixed.

While a new coat of paint can go a long way in improving the look of your garage door, the truth is that door design has come a long way in the years since garages were first installed in homes. Not only are newer doors more in line with current fashion trends, but they are also better sized for today’s cars. A new, contemporary door is a great way to get an immediate boost on the value of your home.
Homeowners have long been warned that torsion springs are extremely dangerous to work with and that replacing them must be left to a professional. But these claims are somewhat exaggerated. If you understand how they work, and you pay attention to what you're doing, you can replace them safely and surprisingly easily. Granted, they're a little spooky to work with at first (partly due to their reputation), but this is a good thing—you really don't want to forget that they're under tension. Thinking about every step — before you take it — is the key to staying safe.
Call us today for new garage door installations, repairs or replacement. Most times a small adjustment is all that’s needed to make your garage door last for years to come.  We fix broken springs, replace rollers, anchors, brackets. Replace bent panels, re-align sensors, replace perimeter seal or bottom seal and much more. We also offer a safety inspection & tune-up services to keep your garage door opener running smoothly.
Over time, the springs in your garage door can wear down and break. While the average cost to repair garage door springs is between $100 and $200, in some cases you may need to replace them instead. Replacement can cost $20-$30 for springs plus labor which can cost up to $180. Here are some signs to watch out for when determining whether repair or replacement is the right course of action:
Because garage doors are large, heavy, and mildly complicated, most people who buy them take advantage of these services. But, if you’re pretty adept at DIY tasks, you can save some money and enjoy the satisfaction of doing the job of installing a sectional garage door yourself. (Sectional garage doors travel up and down on rollers that ride along tracks at each side of the garage doorway.)
DIYers are generally steered away from working with torsion springs because installed springs are always under tension. To safely remove a torsion spring, you have to control the tension by holding the spring with a solid metal winding bar, then you loosen the spring from the rod and manually unwind the spring using two winding rods. The spring is potentially dangerous until it is fully unwound. By contrast, extension springs have little or no tension when the garage door is fully open.

Automatic Garage Door Repair Centennial Colorado 80015


If you have a garage door opener and you suspect a spring has broken, do not disconnect the opener from the door (by pulling the red emergency release handle) while the door is open. If you do, the door can come crashing down under its nearly full weight, with nothing to stop it. This is an extremely dangerous situation. It is never safe to leave the door open when a spring has broken because someone might try to close the door without realizing how heavy it is. Or, they might pull the emergency release handle on the opener. http://www.youtube.com/watch?feature=youtube_gdata&v=Z_eZc-kh40c

My wife and I began having our custom home built in the fall of 2002. We were able to subcontract many phases of the build process & we did all the painting. A highlight of the building experience was choosing precast concrete basement walls (produced in a controlled environment) and installed with great results by one of the TOH partners (Superior Walls). We got that idea based on watching a TOH episode on PBS a few years prior. It was quite the sight for our neighbors and us as the oversize flat bed truck arrived with an overhead crane and began the process of wall installation. It was kind of scary as the the wall sections were put in place. But without the TOH episode and the TOH seal of approval giving us confidence for the precast walls we would have chosen having the concrete walls poured on site. We have uncertain weather conditions here in Western NY during the late fall season. Who knows how pouring the walls on site would have gone. Thank you TOH for the precast wall episodes.

Garage door problems don’t have to mean the end of the world. Garage door repair is typically a one-day process and can be done for only a few hundred dollars. Common garage door repair requests include fixing slow or erratic garage doors, addressing strange sounds coming from the garage door or motor, fixing cosmetic damage such as dents or scrapes, repairing broken doors that are stuck open or closed, and troubleshooting inoperable doors.

Garage Door Repair Companies Centennial 80016


After you’ve ordered your new garage door, we’ll perform a site inspection to confirm your door size. We’ll contact you to schedule the installation, and our professional installers will do the rest. They’ll deliver your door, take down the old door, reconnect your opener if there is one, seal your perimeter and provide a final walk-through where they’ll clean up the area and haul away your old door. Additional fees for haul away may apply in some markets. We are happy to provide answers to questions you may have at the time of your garage door and opener installation. https://www.youtube.com/watch?feature=youtube.be&v=Z_eZc-kh40c

So we’ve put together a guide for all of those who are knee deep in snow, furious because their garage door is not opening or won’t close which will cause garage door problems when it is cold.  If you suspect that you’re suffering from a garage door opener not working in cold weather, look through our troubleshooting tips in order to figure out if this is a small issue you can take care of yourself or if you’re experiencing a more serious problem that should be left to a professional!

With hundreds of moving parts that are all required to work together, it's no surprise that garage doors may need occasional repair and maintenance. Garage door repair services are also required in emergency situations, like when the garage door won't operate and the car is trapped inside or you've accidentally backed into the door when it was closed. Whether it's a specific repair of your garage door opener, a broken spring that needs to be replaced, or a bent or rusted track, The Home Depot's local, licensed service providers can get the job done quickly and efficiently. http://www.youtube.com/watch?v=Z_eZc-kh40c&feature=youtu.be

Your springs may be broken. There are two different types of springs. If your garage door springs are located horizontally at the top of your garage door then it is called a torsion spring. You should check for a gap in between the springs to indicate if they are broken. If your springs are located at either side of your garage door, they are called extension springs. Look to see if a piece of them is hanging on the side of your garage door to indicate if those are broken. If your garage door springs are broken then replacing them is a dangerous process if you have never done it before so you should seek a professional to repair or replace them.
Unlike torsion springs, replacing extension springs has long been given the "green light" for DIYers, primarily because you can complete the job without having to deal with spring tension. The general process is simple and safe: open the door to relieve the spring tension (and secure it open with C-clamps in the tracks); disconnect the spring from the track bracket and the spring pulley, and disconnect the safety cable from one end; install the new spring, reinstall the pulley, and reconnect the safety cable, and you're done. http://www.youtube.com/watch?feature=youtube.be&v=Z_eZc-kh40c
We are the leading supplier in the USA of these DIY bundle kits and make our springs in America - supporting veterans and American jobs. We offer you the same wholesale prices we sell to the experts and all of our parts are superior in quality to China made competitors or knock-offs found on sites like Amazon. Do not risk your garage door with inferior parts. Our springs win awards for a reason. 

Garage Door Repair Bracket Centennial Co 80015


We arrived at a rental property and tried to open garage door to get our vehicle in so we could unload luggage, etc. Could not open from outside. Went into house and, from inside garage, tried automatic opener but this did not work. So in trying to open the door manually, I reached up and pulled on the red cord attached to a lever. What I could not see, and was not expecting, is that the rope was frayed through almost completely. The rope broke when I applied some weight to it, sending me backwards onto the floor of the garage. https://www.youtube.com/e/Z_eZc-kh40c?app=desktop
DIYers are generally steered away from working with torsion springs because installed springs are always under tension. To safely remove a torsion spring, you have to control the tension by holding the spring with a solid metal winding bar, then you loosen the spring from the rod and manually unwind the spring using two winding rods. The spring is potentially dangerous until it is fully unwound. By contrast, extension springs have little or no tension when the garage door is fully open.
Sometimes, you’ll notice that your garage door closes all the way and then immediately goes back up instead of staying in the closed position. This issue usually arises with brand new garage doors that were just installed or older models that may need to be reset. If this happens, the most likely culprit is the open and close limit settings of your garage door opener. http://m.youtube.com/embed/Z_eZc-kh40c
When you install a new garage door, replace all the hardware as well. If your automatic opener doesn’t have an automatic reversing system that includes photoelectric eyes, replace it. Doors with openers also require two extra pieces of hardware that you’ll see in Photo 4: a support strut (usually included in the door kit) and an opener bracket (not included). For doors with torsion springs located over the door, spend the $50 or so to have a garage door professional release the tension.
The technician did a wonderful job - arrived on time and completed the job in less than 2 hours. I would have given him a 5 on everything if he had returned to add the additional piece (a piece that is fixed to the door frame for better insulation) to my door on the outside on the day he said he would come back. The piece he brought was of wrong color and he said he would be back with the right color the first day after New Year's Day to put up the piece. I hope he can come back soon.

Garage Door Repair Installation Centennial 80016


The new opener was installed yesterday and today for a while it wouldn't close properly. The customer service representative said they will probably have to reverse the sensors. However, no one could come out today (Friday) or tomorrow. She will call me by Tuesday of next week to schedule someone to come here. The customer service rep. and the technician were nice but as of now, my new garage opener is not working to my satisfaction.
When a torsion spring is wound up, it grows 2” in length. This is because the spring starts to compress and the metal has to go somewhere. After the spring is wound, the winding cone is clamped down on the torsion shaft so it can turn the drums to wind the cables as the door goes up. Since the end of the spring is “set” on the shaft, a two-inch gap is left when the spring break's. This is the most definite way of determining you have a broken garage door spring.
Although garage door springs can break during any season and at any time, they most commonly break during the winter. This has to do with the temperature change. When the temperature sinks below a specific threshold, the metal will contract. This means it’s extremely possible for your door springs to shrink slightly during the winter months. This is hard on the springs and makes them more likely to break. http://m.youtube.com/watch?feature=player_embedded&v=Z_eZc-kh40c
Rolling sectional overhead garage door spring replacement should cost somewhere between $195 to $300 for a quality set springs (50000 cycle rating). This price will very if the garage door repair company charges a service call fee (trip charge). The most important thing to consider along with price is the quality of the springs and the warranty. There are any company that we use lower or mid quality springs and charge on the higher end because they include a lifetime warranty on the springs. The catch is that this warranty will only covers the spring for life and labor only for 30 days to a year. Look for a company that offers a equal parts and labor warranty. This insures that the warranty represents the rating of the springs that are being installed. For instants, you may buy a 1500 cycle rated spring set (last 3 years +or-) for $200 with a lifetime warranty and 1 year on labor. When a spring brakes after 3 year the spring its self is covered but the labor cost to replace the warranty spring can be between $65 to $100. This can add up over the year as the warranty will not restart at the time of the warranty replacement. On the offer hand, if you purchase a set of springs rated at 50000 cycles (last 10 year +or-) for $270 with a 10 year parts and labor warranty and a spring brakes in 8 years it would be replace at $0 cost. A must batter value! Always check service company review and get the details on the quality of springs a garage door repair company uses and the warranty, part and "labor".

When you're done watching this video you'll know how to determine whether the company you hired to replace your garage door spring installed the right size spring on your door. You'll also learn the consequences to your garage door opener if the wrong size spring is used. If you are having a problem with your garage door spring, the 2:30 minutes you spend watching this video is time will spent.
A new garage door can add serious curb appeal, not to mention myriad home safety benefits. The cost of a new garage door will vary based on the type of garage door you want and the materials it will be made of. You can purchase a new garage door and have the pros install it for you, but proceed with caution as many installers won’t guarantee their labor if you didn’t purchase the garage door through their company. A new door (without installation) may cost anywhere from $200 to $4,000 or more, depending on size, brand and materials. Here are some examples of average new garage door costs, including installation:  

9.9 Go to the other side of the garage door and insert the end of the cable into the drum. Rotate the drum until the cable is tight. Slide the drum against the bearing and push the shaft to the right. The marks should line up. If they don't, figure out why and correct the problem. It could be a stuck cable, the garage floor may have shifted, or the vertical angle that helps support the bearing plate may have loosened and shifted. Many garage doors have been installed with a gap between a drum and a bearing plate. The cable drums should always be flush against the race of the bearings. http://youtu.be/Z_eZc-kh40c
Depending on the type and location of the damage you might have an alternative to replacing panels, or entire garage doors. One solution to give new life to your garage door is repair. Small dents, rot, rust or holes can be repair without replacing. Depending on what wrong with the panel, average prices for repair are $130 for steel door repairs, $190 for wood, $170 for aluminum and $150 for fiberglass. Garage door panel repair can save homeowners money, but should be weighed against garage door panel replacement. http://m.www.youtube.com/embed/Z_eZc-kh40c
We are proud of the work we do in Northwestern North Carolina. We love this community and we love serving it. So whether you think you need a small repair or a major overhaul, we want to be the team that helps you increase the value of your home while making it a safer place to live for you and your family. Our professional and friendly sales team are eager to connect with you, so contact us today and find out just how we can ease your concerns and make transform your garage! 

Garage Door Repair Free Estimate Near Me Centennial 80016


Opening the door yourself is recommended only during an emergency, as there is an increased risk of it getting stuck again-or worse yet, crashing down on top of you. Moving a wooden door could cause damage to the opener, or the top of a steel door might bend underneath the pressure. If you must open the door long enough to drive underneath it, you may want to prop up either side with some 2×4 pieces of lumber to provide added stability. You could also secure your door to its tracks using a pair of vise grips or a couple of c-clamps.
Nothing can be more frustrating than trying to open or close your garage door, but have it get stuck halfway. The most common reason this happens is due to a broken torsion spring, a part that is responsible for providing balance. It is a common problem that has many people saying “My garage door has a broken spring or is stuck, what do I do next”? If you are in this same boat, you’ll find the information below very useful.
To evaluate whether the problem lies with the door or the automatic opener, make sure the door is in the fully closed position, then disengage the opener trolly from the door by pulling the emergency release cord. Try to lift the garage door by hand. If the door opens smoothly by hand, the problem is with the opener. If the garage door still only opens halfway, the problem is with the door.

If this is the problem then you will be able to tell by seeing if your garage door rollers are literally off track. If your garage door panels are not damaged, then you do not need to replace your door. However, the rollers do need to be put back on the track which should be done by a professional. If you are looking for a garage door company that specializes in Garage Doors, Garage Door Repair, or Garage Door Openers, or are just looking for more information, please visit our website at precisiondoor.net. Remember, "We Fix Garage Doors Right"™.

Garage Door Repair In My Area Centennial Colorado 80016


We want to hear from you and encourage a lively discussion among our users. Please help us keep our site clean and safe by following our posting guidelines, and avoid disclosing personal or sensitive information such as bank account or phone numbers. Any comments posted under NerdWallet's official account are not reviewed or endorsed by representatives of financial institutions affiliated with the reviewed products, unless explicitly stated otherwise. https://m.youtube.com/e/Z_eZc-kh40c
After removing the old batteries, make sure the plus and minus signs line up with the plus and minus signs on the inside of the transmitter. Otherwise, the new battery won’t work in the transmitter, and it could give you a false sign that something else may be wrong. Once the battery is in place, test the transmitter, and if it works, replace the transmitter door.
To realign the track, first loosen the screws that hold the track to the frame. Then, gently tap the track with a rubber mallet to move it back into the proper position. Use a level to ensure it’s perfectly straight. Once you have the alignment correct, tighten the screws securely to ensure the track won’t move and cause more issues when opening your garage door. You’ll need to repeat this same process on the other tracks as well, as these may also be out of alignment.
When one or both springs break, gravity takes over and you feel the full weight of the door when lifting or lowering it.  It may be possible to pull the door up by hand, although doing so will likely be very difficult. In most cases, two or more people are needed to raise the door high enough for you to drive your car out of the garage. While single garage doors can typically be lifted, double doors are nearly impossible to manipulate due to their excessive weight. http://www.youtube.com/watch?feature=youtu.be&v=Z_eZc-kh40c
Weather conditions can make rails expand or contract slightly, which requires a little extra pressure from the opener to compensate. Turning the force-adjustment screw increases or decreases the force. However, adjusting the force is not something to play around with unless you are confident you know what you’re doing. The force adjustment signals the opener to stop and reverse when objects are detected in the closing path. Too little force and just about anything will trigger it to stop, but too much force and the garage door might not respond to resistance from something or someone in the path when the door is trying to close.

Garage Door Repair Free Quote Centennial Co


If your garage door track is out of alignment, it can be a serious issue. The metal track your door runs on needs to be aligned properly in order for your door to move. If you see gaps between the rollers and rail, or bends in the rails themselves, you have a problem. The heavy weight of the door can compound these issues and make them worse until it becomes dangerous to operate your door.
The average lifespan of torsion springs is determined by its cycle count. Garage Door Medics provides springs with an average of 25,000 cycles and we can provide custom size springs for any door. The industry standard is 10,000 cycles. When a garage door is used more frequently, the springs may not last as long. If you begin to see signs of wear, it’s time to give Garage Door Medics a call!
You may remember a time as a kid when you and your siblings would close the garage door and run underneath it as fast as possible to make it out before the door closed. Well, on any garage door installed after 1993, that’s no longer possible thanks to two tiny photo eyes on either side of the garage entrance. These photo eyes transmit an invisible beam between each other that detects if anything is in the garage door’s path when it closes. This safety measure is there to prevent automatic garage doors from closing on top of someone or something and causing serious injury or damage to property.

The following procedures are based on my 30 years in the garage door industry. In spite of my high mechanical aptitude, even after 18 years in the trade I lost the end of my left index finger. A few years later I had five stitches in my right thumb, and a year later five stitches in my left thumb. In 2004 emergency room staffs dug steel out of my eye and sewed up my ring finger with eight stitches. The best I can do is help you minimize the risk of injury; that's all I can do for myself. I am not so naive as to think that I have made my last trip to the emergency room. Repairing garage doors, particularly replacing torsion springs, is dangerous work, whether you are a do-it-yourself homeowner or an experienced technician.


If the door closes but then immediately pops open again, you'll need to check the limit settings, which help the mechanism determine how far to move the door in order to close it properly. If the settings are off, the door will hit the ground before the opener believes it should. It will assume that it has hit an obstacle and will automatically backtrack to avoid damage. Check the owner's manual or the buttons on the motor to adjust the limit settings. It may take some trial and error to get the setting just right. http://youtube.com/watch?v=Z_eZc-kh40c
Over time, our reputation has provided us with wonderful opportunities, such as supplying the rolling doors for Paul Brown Stadium while also serving as the service provider for Great American Ballpark. We are proud to be known in this city that we love. And as true Cincinnati fans, we are honored to play a small part helping the teams we root for!
Delivered on time, with the products described: springs, winding bats, & plastic bushing. Quick install, but apparently I measured wrong, so these total length I bought was larger (which is good as there is less stress on the spring). However this did mean that I needed more than the generic rule of 30 1/4-turns of preload. I wound up with 38 1/4-turns per side for the door to balance when open 3' (per familyhandyman.com recommendations). Would definitely do it again. 

After removing the old batteries, make sure the plus and minus signs line up with the plus and minus signs on the inside of the transmitter. Otherwise, the new battery won’t work in the transmitter, and it could give you a false sign that something else may be wrong. Once the battery is in place, test the transmitter, and if it works, replace the transmitter door.


Homeowners have long been warned that torsion springs are extremely dangerous to work with and that replacing them must be left to a professional. But these claims are somewhat exaggerated. If you understand how they work, and you pay attention to what you're doing, you can replace them safely and surprisingly easily. Granted, they're a little spooky to work with at first (partly due to their reputation), but this is a good thing—you really don't want to forget that they're under tension. Thinking about every step — before you take it — is the key to staying safe.
×