9.13 If you have a spring anchor bracket with a fixed steel bearing, check for wear at the point where the shaft and bearing race meet. The shaft needs to be free to slide sideways inside the bearing. File the shaft if needed. Lube the bearing. Notice that only one bearing is needed for two torsion springs. This bearing keeps the shaft from rubbing against the inside of the stationary cones and on the center bracket. Your garage door may not have a center bearing. If so grease the shaft where it will be rubbing the bracket and the insides of the cones.
If you happen to be home when these break, you’ll hear a loud bang from inside your garage. This bang can be so loud that some people might think a firecracker went off inside their garage. That’s because garage doors can be very heavy and despite what most people think, it’s not the garage door opener that does the heavy lifting, but rather the heavy-duty springs of the door.
We are the leading supplier in the USA of these DIY bundle kits and make our springs in America - supporting veterans and American jobs. We offer you the same wholesale prices we sell to the experts and all of our parts are superior in quality to China made competitors or knock-offs found on sites like Amazon. Do not risk your garage door with inferior parts. Our springs win awards for a reason.
Step 1: Check the metal tracks inside the garage. Look at the mounting brackets that hold the tracks to the walls. If they're loose, tighten the bolts or screws at the brackets. Working inside the garage with the garage door closed, examine the tracks for dents, crimps, or flat spots. If there are any damaged spots, pound them out with a rubber mallet, or with a hammer and a block of scrap wood. If the tracks are badly damaged, they should be replaced.
We have had many concerns with our garage opener unit both safety issue and sleepless nights. At this time we are pleased that so far the unit is operating as it should.Hopefully we hope the issue of the unit opening by it self at early morning hours is solved. And if this is so, we want to Thank all involve in bring a satisfactory solution to this nightmare.
Since most yards entertain play activity including baseballs and other sporting equipment, it's no surprise that garage doors experience broken glass from time to time. Regardless of the cause, it's important to repair glass quickly, since broken glass in a garage is a safety issue, a security problem, and an invitation to every bird and insect in the neighborhood to take up residence in your garage. Fortunately, it's not difficult to replace a pane of glass. The techniques are exactly the same as for replacing glazing in a house window.
They were quick, friendly, and highly professional. Little things like making me enter security code from the other side of the closed garage door revealed their attention to security They had to run to Home Depot to get a small block of wood to fix an existing problem with the door — They didn’t charge me extra. Quite unexpected & appreciated. 10 out of 10 https://m.youtube.com/embed/Z_eZc-kh40c
10.13 Slowly pull down on the winding bar until the garage door rises 3" and the roller hits the vise grip on the track. The door will usually drop back down and raise the bar. If it doesn't, lift the end of the bar until the door closes. If the door comes up by itself when you hold the bar lightly, the springs are either over wound or they are too strong. You may need to remove 1/4 to 1/2 turns from the springs. If the door comes up on its own, you either have to many turns on the springs or you have the wrong springs. This can be very dangerous. We recommend getting professional help. Removing the winding bar could cause the garage door to knock you off the ladder.
Unlike torsion springs, replacing extension springs has long been given the "green light" for DIYers, primarily because you can complete the job without having to deal with spring tension. The general process is simple and safe: open the door to relieve the spring tension (and secure it open with C-clamps in the tracks); disconnect the spring from the track bracket and the spring pulley, and disconnect the safety cable from one end; install the new spring, reinstall the pulley, and reconnect the safety cable, and you're done.
If you want to do the repair yourself, get several phone estimates first, because rates vary widely among service companies. Most garage doors are heavy (200 to 300 lbs.), so call in three strong friends to help you lift the door and hold it open while you lock it in the full raised position with a locking pliers. Then move your vehicles and have your friends help you lower the door.

When you know you’re in range and the door still won’t open, check to make sure the antenna is hanging down from the motor inside your garage and nothing is blocking it. Your antenna must be free from any obstruction to clearly receive the signal to open and close the door. Also inspect the antenna for any signs of damage. If it looks like there has been damage to the antenna, you’ll need to call your garage door technician to come out and replace it.

9.8 Twist the garage door shaft to tighten the cable on the drum. While twisting, vise grip the shaft as shown to keep the cable tight on the drum. The top of the vise grip should be tight against the garage header. This will keep the cable snug on the first drum while you install the cable on the other drum and position it in place. It also keeps the shaft from turning and the cables peeling off when you wind the springs. That one grip can save many hours of walking back and forth and having to level and re-level the garage door after winding the torsion springs.
The track is secured with these little brackets and they're adjustable. There's a slot that it rides in so you can unscrew it here and adjust it if you need to. And you're going to have to pay attention and look at it closely to make sure it's in the right spot, but it's not that tricky and you can do it. And usually one side is out of alignment so you can compare it to the other and then adjust it as needed. https://youtube.com/watch?feature=youtu.be&v=Z_eZc-kh40c
1. Garage door springs do almost all of the work of lifting your door regardless of the door being manually or automatically operated. The spring makes it possible for anyone to lift a product that might weigh one hundred pounds on the low end and many hundreds of pounds on the high end. Not only can anyone lift it – most can do it with one hand! In other words, the garage door spring does a lot of work.

Garage Door Repair Centennial Colorado 80015


Measure the various areas where the door will be installed: door-opening height and width, headroom (from top of opening to ceiling), and back room (length of garage). For the headroom, you should have about 10" to 12" of space, depending on the spring system you're installing. For the back room, you should have the door height, plus another 18" or more of space.
When you know you’re in range and the door still won’t open, check to make sure the antenna is hanging down from the motor inside your garage and nothing is blocking it. Your antenna must be free from any obstruction to clearly receive the signal to open and close the door. Also inspect the antenna for any signs of damage. If it looks like there has been damage to the antenna, you’ll need to call your garage door technician to come out and replace it.
Extension springs are long, lighter-weight springs that run perpendicular to the door and are mounted above the horizontal portions of the door tracks. These springs are tensioned by stretching out, using cables and pulleys, as with the torsion system. Because extension springs are merely suspended between two brackets (they are not mounted to a rod, like torsion springs), they must have a safety cable running through each spring. This helps contain the spring in the event of a breakage. Without the safety cable, a spring breaking under tension is a very serious safety hazard. If you have old springs that don't have safety cables, you should install them even if you aren't replacing the springs.

Garage Door Repair Free Estimate Near Me Centennial Colorado 80015


10.3 At this point you will wind the spring. Notice that the end of the spring on the winding cone points up when facing you. You will wind both springs up and counter intuitively as if you are trying to unscrew the winding cones from the ends of the springs. Begin by turning the spring up 1/4 turn until it meets resistance. This is your first quarter turn. Count "one." Next, insert the bar and raise it 90 degrees. Insert the second bar. This is "two." As you wind the spring it should grow in length the thickness of one coil for every turn. The cone should cover your mark after the first couple turns. Many garage door tradesmen mark the torsion springs with chalk or paint, but this often generates confusion.

My wife and I began having our custom home built in the fall of 2002. We were able to subcontract many phases of the build process & we did all the painting. A highlight of the building experience was choosing precast concrete basement walls (produced in a controlled environment) and installed with great results by one of the TOH partners (Superior Walls). We got that idea based on watching a TOH episode on PBS a few years prior. It was quite the sight for our neighbors and us as the oversize flat bed truck arrived with an overhead crane and began the process of wall installation. It was kind of scary as the the wall sections were put in place. But without the TOH episode and the TOH seal of approval giving us confidence for the precast walls we would have chosen having the concrete walls poured on site. We have uncertain weather conditions here in Western NY during the late fall season. Who knows how pouring the walls on site would have gone. Thank you TOH for the precast wall episodes.


Most homeowners never know they have a broken garage door spring until they try to leave their home. You go in the garage to open the door, push the wall button, and the door only goes up 6”. The reason for this is the garage door opener force or sensitivity has activated, causing the opener to stop pulling the door up. This is a safety feature built into most garage door openers. It is actually a good thing when the open force activates to prevent any damage to your garage door or opener.

I'm getting a good laugh on all the comments on "Garage Door Nation" on how easy they or people make it sound to order and change out their torsion springs. First off, if you do your shopping, the savings is about $50 - $75 having a company do it. Is it worth the 3 days wait without the use of your garage door, the safety risk and your time doing it yourself? If yes, then go for it!
Keep in mind, the pulley is often cycled through an enclosed casing that is difficult to lubricate directly. By applying enough lubricant to the pulley, you’re ensuring that the whole lifting mechanism is properly lubricated. Furthermore, a jam in this portion of the lifting mechanism is a time-consuming and potentially labor expensive repair that requires a service professional.

Garage Door Repair Emergency Centennial Colorado 80015


If a roll-up door, assuming you have not put in cabinets or anything that prohibits sliding the shaft sideways about 2-3 feet out of the spring to change it, then about $200-250 should do it for a 2-car garage door. If he has to disassemble the brackets to remove the springs because the shaft cannot slide sideways enough to get the springs on/off, then probably another $50-100.

My garage door torsion spring broke so I decided to replace it myself. Shipping was next day. I got the torsion spring rod at a local hardware store. Easy to install once I figure out how to lock down the rod from moving and loosening the door cable on the side. Instructions tells you how to do it. Great replacement spring and save $$$ doing it myself. https://m.youtube.com/watch?v=Z_eZc-kh40c
One thing to consider - assuming you have 2 springs and an opener, unless the other spring is quite new, you should replace it at the same time, first because it will probably break fairly soon anyway and changing two is only about $50 more than changing one, and because the springs on both sides should be of equal stiffness - if not, then the door will be unevenly weight compensated and try to open cockeyed, increasing wear and risk of damaging the motor.
We have had many concerns with our garage opener unit both safety issue and sleepless nights. At this time we are pleased that so far the unit is operating as it should.Hopefully we hope the issue of the unit opening by it self at early morning hours is solved. And if this is so, we want to Thank all involve in bring a satisfactory solution to this nightmare.

Step 5: Check for loose hardware, and tighten as needed. On swing-up doors, check the plates where the spring is mounted to be sure the screws are tight, and tighten any loose screws. On roll-up doors, check the hinges that hold the sections of the door together; tighten any loose screws, and replace any damaged hinges. Sagging at one side of the door can often be corrected by servicing the hinges. If a screw hole is enlarged, replace the screw with a longer one of the same diameter, and use a hollow fiber plug, dipped in carpenters' glue, with the new screw. If the wood is cracked at a hinge, remove the hinge and fill the cracks and the screw holes with wood filler. Let the filler dry and then replace the hinge. If possible, move the hinge onto solid wood.
These instructions are for doors with cable drums and cables that look similar to those in the picture below. The next part beyond the end of the spring assembly is the cable drum. The drum is cast aluminum alloy 4" in diameter and 12.6" in circumference around the flat portion. Just beyond the cable drum is the end bearing plate. The cable unwraps off the back of the drum between the drum and the garage wall or jamb and travels down alongside the door, inside the track brackets and behind the roller stems as shown.
Annual maintenance. Make an annual check of all nuts and bolts on rails and rollers to make sure they’re firmly tightened. Check the condition of all cables to make sure they’re not worn or frayed. Lubricate rollers and springs with a garage-door lubricant (see How to Fix a Noisy Garage Door for maintenance and problem-solving tips). The door should operate smoothly and be properly balanced. Check the balance by disconnecting the opener and lowering the door halfway- the door should hold its position. If it doesn’t, adjust the spring tension or replace the springs.

Garage Door Repair How Much Centennial Colorado 80016


6.7 It's now time to unwind the spring. Firmly position yourself on a steady ladder beside the garage door. Next, insert the bar into one of the holes of the winding cone. Make sure it goes all the way in. It should click when your bar hits the core. If you want to test the force you will be handling before loosening the set screws, push up on the bar one quarter turn and bring it back down. Next, while grasping the other end of the bar firmly, loosen the set screws with an open-end wrench or small adjustable wrench loose enough to come free should the cone spin. Be prepared for the torque to be transferred to the bar.	

There’s never a convenient time for your garage door springs to break. When this crucial component gives out, you need a repair job or replacement as soon as possible. That’s why Marvin’s Garage Doors is available 24/7 for emergency service. When that emergency arises, or you’re stuck in your garage and unable to get out to get to work, simply give us a call on our emergency line at 336-813-2601.
Insulation increases the efficiency of your door and can lower your electric will. You need R-value garage doors. These type of doors keep out hot and cold air and also provide a sound barrier between the outside and your garage. Insulated doors use polyurethane or polystyrene foam as insulation inside the door. More information about garage door replacement cost.

I purchased a garage door and opener and had HD install it. It was around $3600 and when the price increased by about $800 I called right away to pay it with no delay (these are all estimates written from memory). Anyway, I I bought the garage so that the front of the house would be prettier and it is but the old garage worked fine and I don’t even have a car in it so I don’t open and close it all and it actually only gets opened 2-3 times a month when a friend who stores their car there uses it. However, soon after the garage was installed, this friend told me the garage was working intermittently. When I called HD to come look at it, they said I would have to pay around $85 to have it looked at which didn’t make sense to me since it was brand new and almost immediately not working so it was likely a problem with the product or installation. HD would not provide immediate assistance to fix the problem, they insisted other steps which were unreasonable given it was a new garage and this request added great difficulty for me. Five months later after this back and forth calling to have someone from HD to just come and fix it, I went into the Huntington Beach store, spoke with Ryan who was polite and with little to say, he said I’ll put you on the list for an appointment and they will call in 24-48 to book a day and time. I was thankful. I also expressed my concern that I would not be charged for this visit and he said no unless it wasn’t covered under warranty. Two days later the installer called and said it will cost to around $95 just to show up. They arrived later that week, charged $95 and fixed the problem with no additional fee. If the garage was being used the way most garages are used and it was out of warranty, I could understand for a fee to cone out and look at it but because it stopped working almost Immediately and all the fuss and delay to have it fixed by HD was disappointing. When you gave me a quote then raised it by 20%% I paid immediately and without hesitation but this service was not reciprocated. I may have multiple projects at multiple sites but even if that weren’t the case, I would hope you would keep up your good costumer service history otherwise, your competitors willl slowly be better. Kindly return the fee charged for this service. Read less
4.4 Take the spring on the left and place it at the left end of the door as pictured here. Notice that the end of the wire points to the right toward the center of the door. This is a right wind torsion spring. It will go above the garage door on the left side of the spring anchor bracket. The winding cone at the other end of this spring is usually painted red.
×