Inspect the area around your garage door to see if something is blocking the photo eye sensors. Then look at the tracks to see if there is any buildup on the inside. You’ll need to get a step ladder to look at the tracks on the top part of your garage, as it will be difficult to see from ground level. It may also not be a bad idea to proactively wipe down your garage door tracks periodically to prevent this type of buildup from occurring. Running a damp rag along each track should be enough to remove anything that’s lingering on the tracks. https://www.youtube.com/attribution_link?a=Z_eZc-kh40c&u=%2Fwatch%3Fv%3DXXXXXX%26feature%3Dshare

In order to prevent injury, garage doors automatically reverse if they come into contact with an obstacle. When the door closes halfway but then reverses for no apparent reason, this may be a sign that there is something preventing it from closing, something that you can't see. Check the tracks for stuff like dirt, rocks, bits of trash, or other debris. Give the tracks a wipe-down to dislodge anything that might be getting in the way.
Instead, try other methods that might break the frozen connection between the door and the floor. For example, you can use a heat gun or hair dryer to melt the ice and free the door. Standard de-icing products can also work. And if you are careful not to damage the door or the seal on the bottom of the door, you can use a flat shovel or similar tool to chip away at the ice.

Maybe the battery died or a spring broke, but you can't get into the garage to even see what the problem is. If the garage door is the only way in or out, or if you can't find the key to the door, you'll have to either find a way to break in or call a locksmith. As a preventative measure, it's smart to keep a spare key or install an emergency key release that would allow you to release the emergency disconnect to the operator so you can manually raise the door. https://youtube.com/e/Z_eZc-kh40c?app=desktop
9.12 It is now time to secure the torsion springs in the middle. For various reasons, many installers will offset the center bracket several inches from the center of the door. Offsetting the bracket makes it easier to work around the opener bracket without causing any problems in the operation of your garage door, but offsetting the bracket is not necessary. If you have a slotted center bracket, remove the vise grip and lube the shaft where it turns inside the bushing. Position the shaft so it is the same distance from the header as it is at each end. The shaft should be straight and parallel to the header.
2. These springs do wear out over time – in fact, they are commonly rated with what is called a cycle life. The average standard cycle life is ten thousand cycles with each cycle being one opening and closing of the door. This means for a door that sees four cycles per day you might expect to replace your springs after somewhere close to seven years of use.

In need of garage door repair? Contact one of our many well-trained garage door repair professionals today to provide your garage door system with the recommended service and maintenance procedures for smooth and reliable operation. Our garage door repair professionals are here for you, whether you want to fix your existing garage door or buy a new garage door. Are you looking to replace a garage door spring, cable or roller or searching for 'garage door repair near me'? Use our distributor locator below: 
Because garage doors are large, heavy, and mildly complicated, most people who buy them take advantage of these services. But, if you’re pretty adept at DIY tasks, you can save some money and enjoy the satisfaction of doing the job of installing a sectional garage door yourself. (Sectional garage doors travel up and down on rollers that ride along tracks at each side of the garage doorway.)

Garage Door Repair Companies Centennial Co 80015


Luckily, there is a bit of science to questions of garage door repair and replacement. That’s why we’ve put together this guide on when to replace a garage door. We’ll prepare you to compare repair vs replacement garage door costs. We’ll discuss the ways in which repairs are the most affordable option while also exploring those moments when replacement will in the end provide you with more value added.
The material and style of your door as well as the replacement parts needed will impact the total cost of your project. It would cost less to install a steel door with no opener then it would to install a wood door with an opener etc… High tech doors come with enery-effecient glaze and thick insualation as well as finshed interiors and other upgrades. These doors are more expensive but are more reliable and durable.
These instructions were first posted in 2005, and they were updated in August of 2008. I have been frank about the hazards of garage door repairs and about my own accidents incurred while replacing torsion springs. For what it's worth, you might be surprised to know that I, too, have benefitted from producing these instructions. I have not had any garage door accidents since we first published these on the web in 2005. And, in as much as I have helped keep other DIY-ers out of the emergency room, I consider myself somewhat of a medical practitioner.

The material and style of your door as well as the replacement parts needed will impact the total cost of your project. It would cost less to install a steel door with no opener then it would to install a wood door with an opener etc… High tech doors come with enery-effecient glaze and thick insualation as well as finshed interiors and other upgrades. These doors are more expensive but are more reliable and durable.
Over time, the springs in your garage door can wear down and break. While the average cost to repair garage door springs is between $100 and $200, in some cases you may need to replace them instead. Replacement can cost $20-$30 for springs plus labor which can cost up to $180. Here are some signs to watch out for when determining whether repair or replacement is the right course of action:
Even though most of us are likely used to seeing this small spring in place on our garage door, we don’t often think too much about it, and we simply count on it working when we need it to. Unfortunately, it doesn’t last forever and will eventually need to be replaced. It’s best to be proactive and notice when it begins to look worn down before it actually breaks. Otherwise, you may find yourself trying to open the garage door to drive to work one morning, only to find that the door won’t open because the spring is broken.
You are about to leave this Custom Door & Gate and enter a third-party site. Custom Door & Gate and Installed Building Products have no control over, and accept no liability, obligation, or responsibility for, the contents or performance of other websites. Any such link does not constitute an endorsement or any representation regarding, the linked website, its content, its owner, its performance, its owner’s products or services, or any forward-looking statements found in.

Garage Door Repair Bracket Centennial Colorado 80016


Garage doors eventually begin to break, look terrible and pose safety risks. How old is your garage door? Have you ever had a safety inspection performed? Garage door safety should always be a top priority as it could cause serious injuries and cost you the expense and trouble of personal injury lawsuits. Our blog will show you what you need to know about garage door safety inspections to assist you with the inspection and upgrades of your home's garage door. Hopefully, what we show you will help to keep your friends and family safe from harm when they visit you.

Garage Door Repair Near Me Centennial Colorado 80015


Roberto was very courteous and explained the details of what he was doing. He also pointed out a repair I might consider having done (replacement of the bottom panel of my door) and asked the office to follow up with me on this. Someone did follow up with me and since replacement of the bottom panel is not an option and I would have to replace the door, I decided that I can wait.

Doors with extension springs have two sets of pulleys (which are sometimes called _sheaves_): one at the end of each spring and one at the top of the vertical door track. They also have two cables on each side. One cable attaches to the bottom of the door, runs up and over the pulley above the door and around the spring pulley and then attaches to the door track bracket. The other cables are safety cables that run through the middle of the springs and are fixed to a track bracket at both ends. These cables restrain the springs if they break under tension. All extension springs must have safety cables.

Garage Door Repair Near Me Centennial Colorado


9.13 If you have a spring anchor bracket with a fixed steel bearing, check for wear at the point where the shaft and bearing race meet. The shaft needs to be free to slide sideways inside the bearing. File the shaft if needed. Lube the bearing. Notice that only one bearing is needed for two torsion springs. This bearing keeps the shaft from rubbing against the inside of the stationary cones and on the center bracket. Your garage door may not have a center bearing. If so grease the shaft where it will be rubbing the bracket and the insides of the cones.
Install the center bearing and the right spring, then secure the cones. Slide the torsion bar to the left then add the center bearing. Slide the right spring onto the bar and press the bearing into the stationary cone. Connect both of the stationary cones to the center bracket with the nuts and bolts you removed previously. Remove the locking pliers or clamp from the center bracket.[10]

Garage Door Repair Guy Centennial Co


Over time, our reputation has provided us with wonderful opportunities, such as supplying the rolling doors for Paul Brown Stadium while also serving as the service provider for Great American Ballpark. We are proud to be known in this city that we love. And as true Cincinnati fans, we are honored to play a small part helping the teams we root for!

Garage Door Repair In My Area Centennial Co 80015


Our garage door broke 3 days before Christmas, trapping my car inside. We contacted our home warranty, and within 24 hours, Sears called with an appointment time for the next day! I was so impressed! I thought, for sure, with the holidays, we would have to wait. When the technician showed up, he was so friendly. Unfortunately, the repair was not covered under our warranty, but he was able to help us get a good deal on a new spring and still make the repairs that day before he left. He also gave us great advice on how to keep the spring lubricated so it would not break again. I felt like he really went above and beyond to provide great service. Since moving into this new house in August, we have used Sears for several things now, and have been very pleased with the service. It's nice to see that in an age when so many companies just put customer service on the back burner in order to meet their bottom line, Sears still really cares and makes their customers feel important. Thanks for taking care of us this Christmas!

Garage Door Repair Companies Centennial Co 80016


Nothing can be more frustrating than trying to open or close your garage door, but have it get stuck halfway. The most common reason this happens is due to a broken torsion spring, a part that is responsible for providing balance. It is a common problem that has many people saying “My garage door has a broken spring or is stuck, what do I do next”? If you are in this same boat, you’ll find the information below very useful.

Dallas Texas, Plano TX, Garland TX, Highland Village, Lakewood, Las Colinas, Lewisville, Little Elm, Grapevine, Haltom City, Hurst, Keller, Forney, Carrollton, McKinney TX, Murphy Texas, Oak Lawn, Arlington TX, Parker TX, Plano, Preston Hollow, Richardson TX, Denton, Addison, Allen, Bedford, Coppell, Crowley, DeSoto, Euless, Flower Mound, Rockwall Texas, Garland Texas, Rowlett TX, Sachse TX, The Colony TX, Lavon Texas, Fort Worth TX, East Dallas, North Dallas, Wylie TX, White Rock Lake, area Lakewood, North Richland Hills TX, Benbrook, Burleson, Waxahachie, Red Oak, Irving TX, Mesquite TX


We are the leading supplier in the USA of these DIY bundle kits and make our springs in America - supporting veterans and American jobs. We offer you the same wholesale prices we sell to the experts and all of our parts are superior in quality to China made competitors or knock-offs found on sites like Amazon. Do not risk your garage door with inferior parts. Our springs win awards for a reason.
Like any mechanical part, garage door springs deteriorate due to normal wear and tear. Over time, the steel that makes up the springs weakens until they eventually break. Under normal circumstances, garage door springs have a life expectancy of 10,000 cycles of opening and closing. This equates to five to seven years, but along the way, there may be signs of problems that can occur before the springs actually stop working.

Garage Door Repair Guy Centennial Co 80015


6.10 If the garage door comes off the floor when you pull down on the bar, and if the cone still won't loosen, tap the bar next to the cone with a hammer to force the cone beyond the swollen portion of shaft. Maintain a firm grip on the bar; keep it firmly inserted completely into the cone; and be prepared at all times for the cone to slip, break, explode or break free from the shaft and yank the bar down.

Garage Door Repair Installation Centennial Colorado 80015


With hundreds of moving parts that are all required to work together, it's no surprise that garage doors may need occasional repair and maintenance. Garage door repair services are also required in emergency situations, like when the garage door won't operate and the car is trapped inside or you've accidentally backed into the door when it was closed. Whether it's a specific repair of your garage door opener, a broken spring that needs to be replaced, or a bent or rusted track, The Home Depot's local, licensed service providers can get the job done quickly and efficiently. http://www.youtube.com/watch?v=Z_eZc-kh40c&feature=youtu.be
If one of your door springs just broke and you are looking for instructions to decide if you can change the spring or springs safely and correctly, this page should help. DO NOT OPEN AND CLOSE YOUR GARAGE DOOR. Wooden garage doors are heavy and will probably damage or ruin the opener. The tops of steel doors often bend when operated with broken springs.
Garages are the ultimate convenience come winter time. While people who park their car outside are dealing with dead batteries and scraping ice off of their windshields, your car is parked in a cozy garage, oblivious to the freezing conditions outside. When the sidewalks are slick, you don’t have to worry about slipping on the ice while you’re carrying a grocery bag full of eggs. Plus it’s just so much nicer to get into a car that isn’t freezing cold every morning on your way to work!
Our garage door broke 3 days before Christmas, trapping my car inside. We contacted our home warranty, and within 24 hours, Sears called with an appointment time for the next day! I was so impressed! I thought, for sure, with the holidays, we would have to wait. When the technician showed up, he was so friendly. Unfortunately, the repair was not covered under our warranty, but he was able to help us get a good deal on a new spring and still make the repairs that day before he left. He also gave us great advice on how to keep the spring lubricated so it would not break again. I felt like he really went above and beyond to provide great service. Since moving into this new house in August, we have used Sears for several things now, and have been very pleased with the service. It's nice to see that in an age when so many companies just put customer service on the back burner in order to meet their bottom line, Sears still really cares and makes their customers feel important. Thanks for taking care of us this Christmas!
"Springs get a lot of wear and tear because they handle the weight of the door," says Paul Cardone, owner of Garage Door Guru in Charlotte, North Carolina. "The type of spring you have depends on the type of door you have — the heavier the door, the more heavy duty the spring. They're full of tension and made of metal, so after so many cycles, they just snap and break."

Garage Door Repair Estimates Centennial Colorado


Doors with extension springs have two sets of pulleys (which are sometimes called _sheaves_): one at the end of each spring and one at the top of the vertical door track. They also have two cables on each side. One cable attaches to the bottom of the door, runs up and over the pulley above the door and around the spring pulley and then attaches to the door track bracket. The other cables are safety cables that run through the middle of the springs and are fixed to a track bracket at both ends. These cables restrain the springs if they break under tension. All extension springs must have safety cables. 

Automatic Garage Door Repair Centennial Co


If the door only goes up six inches and stops, or moves very slowly when using your remote, you could have a broken spring as well. Some customers will notice that the top section of their door is bent or that the door falls very quickly when lowering. Your door may be “crooked” or jerky when going up and down, and both of these signs indicate your torsion spring is in poor condition and very likely to break in the near future. Any time you hear a loud “popping” noise while operating, you should inspect your torsion spring immediately for signs of damage.


Like any mechanical part, garage door springs deteriorate due to normal wear and tear. Over time, the steel that makes up the springs weakens until they eventually break. Under normal circumstances, garage door springs have a life expectancy of 10,000 cycles of opening and closing. This equates to five to seven years, but along the way, there may be signs of problems that can occur before the springs actually stop working.
When a torsion spring is wound up, it grows 2” in length. This is because the spring starts to compress and the metal has to go somewhere. After the spring is wound, the winding cone is clamped down on the torsion shaft so it can turn the drums to wind the cables as the door goes up. Since the end of the spring is “set” on the shaft, a two-inch gap is left when the spring break's. This is the most definite way of determining you have a broken garage door spring.

Garage Door Repair Images Centennial Colorado 80015


Noisy garage doors cause all kinds of problems, especially for anyone who has to sleep above or next to the garage. Fortunately, most noisy garage doors can be fixed with a combination of routine maintenance and the replacement of a few parts. If the basic maintenance tips described above don't quiet a noisy garage door, it's possible that the door's hinges need to be replaced.
There’s nothing more frustrating than attempting to open or close your garage door only to find that it simply won’t budge. In some cases, your garage door may even open or close halfway only to get stuck in the process. The very first thing that you should do if your garage door seems to be stuck is to check the batteries in your remote. You’d be surprised at how often this is the root of the trouble. If dead batteries were not the issue, then use the following four tips to further troubleshoot your garage door.
After you’ve ordered your new garage door, we’ll perform a site inspection to confirm your door size. We’ll contact you to schedule the installation, and our professional installers will do the rest. They’ll deliver your door, take down the old door, reconnect your opener if there is one, seal your perimeter and provide a final walk-through where they’ll clean up the area and haul away your old door. Additional fees for haul away may apply in some markets. We are happy to provide answers to questions you may have at the time of your garage door and opener installation. https://www.youtube.com/watch?feature=youtube.be&v=Z_eZc-kh40c

Test the door balance. A garage door should require only a few pounds of pressure to move it up and down. If springs wear out and lose their resiliency, a power garage door opener may need to work extra hard to lift the door. This can quickly wear out the motor on the opener. Replacing worn-out springs is usually a job for a professional technician.


I'm getting a good laugh on all the comments on "Garage Door Nation" on how easy they or people make it sound to order and change out their torsion springs. First off, if you do your shopping, the savings is about $50 - $75 having a company do it. Is it worth the 3 days wait without the use of your garage door, the safety risk and your time doing it yourself? If yes, then go for it!
Whether you're planning on moving in the future or you're fixing up your forever home, replacing a garage door can provide an excellent return on investment and boost your home's resale value. According to Remodeling magazine's 2016 Cost vs. Value report, garage door upgrades provide a nationwide average return on investment of over 90%, making it one of the top five home improvement projects. To learn more about the cost of installing garage doors, visit our garage door and opener installation and repair cost guide.
Garage door problems don’t have to mean the end of the world. Garage door repair is typically a one-day process and can be done for only a few hundred dollars. Common garage door repair requests include fixing slow or erratic garage doors, addressing strange sounds coming from the garage door or motor, fixing cosmetic damage such as dents or scrapes, repairing broken doors that are stuck open or closed, and troubleshooting inoperable doors.
If you haven’t looked at garage doors lately, prepare to be pleasantly surprised. We’ve taken the garage door and made it stylish with designs to complement both classic and contemporary homes while still keeping the functionality you desire. A garage door can represent more than 30% of your home’s curb appeal, which makes choosing the right design especially important – and Home Depot has the widest selection available. With over 1,000 different garage door designs in wood, steel, composite, aluminum and glass, you’re sure to find the perfect style to transform your garage… and your home.

Garage Door Repair Centennial Colorado


Widths - in addition to doors coming in a range of styles, they can be found as double-width and single-width styles. There are some serious considerations when opting for one over the other. For example, if a homeowner decides to use a single door that covers the entire opening of a two-car garage they will have to make serious structural modifications to the entry way;

It is very important that the replacement springs are calibrated for the weight of your door. Using the wrong size garage door springs will caused the to not function properly and could also cause the opener to break much quicker. Replacing extension springs can be very dangerous and if done wrong can harm someone using the garage door. Make sure you call the Garage Door Doctor to ensure your garage is repaired properly!
In need of garage door repair? Contact one of our many well-trained garage door repair professionals today to provide your garage door system with the recommended service and maintenance procedures for smooth and reliable operation. Our garage door repair professionals are here for you, whether you want to fix your existing garage door or buy a new garage door. Are you looking to replace a garage door spring, cable or roller or searching for 'garage door repair near me'? Use our distributor locator below: 

Clearly there is a lot going on with your garage door and it takes trained and qualified experts to properly install, maintain, repair, and replace them. The experts and On Track Garage Door Services have the tools, skills, training to get your garage door fixed the first time. In addition we can help you fix your garage door affordably and offer many options from your basic garage door to custom wood styles. To find out how much your garage door repair will cost in Phoenix, Scottsdale, Mesa, Chandler or anywhere else, give us a call at 480-641-2301 or use our Contact Page.
In most cases, only one spring breaks or wears out at a time, and you can get away with replacing just the failed spring. But this is a little like replacing old car tires one at a time. You'll get the best performance if all the springs are new and have the same strength. Extension springs are replaced individually, making it more tempting to replace just one. With torsion springs, you have to disassemble everything to replace either spring, so it makes sense to swap out both springs during the repair.
Remove the clamps and pliers from the torsion tube and track, and lift the door about 3 ft. by hand. If the door springs are properly adjusted, the door should stay in place when you let go. If the door falls when you let go, add a quarter turn to each spring. Repeat if necessary. If the door continues to open on its own, release spring tension in quarter-turn increments until the door stays in place when you let go. Then reconnect the opener.

If your garage door is equipped with only one torsion spring, it will be much harder to get your door open. You will need to get 2-3 people to help lift the door up because the full weight can be anywhere from 150 to 300 pounds. We don’t recommend lifting the door when the spring break's due to the danger of it falling on someone. If you absolutely must get your garage door open, raw strength is what you need. When you get the door in the up position, use vise-grips or a c-clamp on the track below the bottom roller to hold the door in the up position.
It is very important that the replacement springs are calibrated for the weight of your door. Using the wrong size garage door springs will caused the to not function properly and could also cause the opener to break much quicker. Replacing extension springs can be very dangerous and if done wrong can harm someone using the garage door. Make sure you call the Garage Door Doctor to ensure your garage is repaired properly!
Often companies will show different types of springs like oil dipped, galvanized or powder coated and try to convince you that one is longer life than the other and that is why it is going to cost this much instead of that much. Galvanized and Powder coated are great for coastal areas as a rust preventative but do not change the cycle life and do not cost but a few dollars more.
Because your garage door can be customized, pricing varies. Our Clopay configurator will help you review pricing as you begin your project. You’ll start with your door size and whether you need a single or double car door. Next, you can choose the collection of door, which gives you options of various materials and styles. Then, you’ll choose your construction, which allows you to decide what you need in terms of energy efficiency, durability and noise control. Lastly, you will be able to visualize the design and see an end price. Other optional add-ons include windows, decorative hardware, smart features and the r-value. However, you do not have to use the configurator. We also install standard garage doors that have not been customized so you know the product price early on in the process.
Springs are one of the primary components in all garage door systems. Torsion springs are usually mounted horizontally over the door opening. As the door closes, cables add tension to the springs and as the door opens that tension is released. The opening of the door causes the springs to unwind in conjunction with the weight coming off the door. This achieves a natural buoyancy. However, as the door moves up and down over time and the cycle count rises, the steel in the torsion springs will grow weak and will no longer be able to create energy or lift your garage door.

Garage Door Repair Bracket Centennial Co 80016


If you happen to be home when these break, you’ll hear a loud bang from inside your garage. This bang can be so loud that some people might think a firecracker went off inside their garage. That’s because garage doors can be very heavy and despite what most people think, it’s not the garage door opener that does the heavy lifting, but rather the heavy-duty springs of the door.


5.1 With the cables still tight on the drums, mark the drums and torsion shaft at each end with a file or a marking pen. If at least one of the springs is still wound, don't touch the cable drums and don't grab the shaft. If the cable breaks, the drum could spin and the cable rip through muscle and bone. If the set screws aren't tight enough, the shaft could spin and cause injury.
You garage door is one of your primary entrances to your home so you want to know that they are functioning properly at all times. If you are having complications with your current garage door, then you need to hire a professional garage door company to determine if it needs to be repaired or replaced. Included are the average garage door repair costs in 2019, for the United States. I’ve also included some garage door repair costs pictures, graphics and graphs that include high, low and average costs for garage door repair, installation and replacement costs. It also includes garage door part repair and replacement costs. http://youtube.com/embed/Z_eZc-kh40c

From a big-box store, basic garage door cables can run between $8 and $20, depending on the product. Your pro may charge you a different cost if they provide the cables. Your cables may not need to be replaced if they have simply come off the track, but broken cables will need to be completely removed and replaced. In either instance, the pros will need to secure or take down the door; unwind the springs; reset or replace the rollers, cables, and drums; and then wind the springs once more. For example, a pro could reset cables that have come off the track for $129.99. The average national cost for a garage door repair specialist is $80 - $110 per hour and the typical cost to replace a broken garage door cable is anywhere from $130 to $200. https://m.youtube.com/v/Z_eZc-kh40c

Finally, we also carry any and every residential garage door product that you need to have a state-of-the-art, secure and safe garage door. We are proud certified dealers of Clopay doors, the most durable and versatile doors on the market. With over fifty years of garage door manufacturing experience, you can trust Clopay quality, just as you can trust our team to install these highest-quality doors.

Garage Door Repair In My Area Centennial Co 80016


Garage door springs come in two styles: torsion (see above), which mounts on the header above the door, and extension (Photo 1), which floats above the upper roller track. In the past, extension springs were safer to install but didn’t have containment cables running through the center of the spring. Without cable, these springs become dangerous, heavy whips when they break. They also tend to be noisier than torsion springs, and we recommend you use them only if you don’t have the 12 in. of headroom above the door that a torsion spring requires.
The garage door opens and closes many times throughout the year, and something may blow inside. While it is usually something such as loose leaves or small amounts of dirt, the rails that the door travel along can collect this loose debris. Over time, the buildup of debris creates a blockage on the rails. Note where on the rails the door is stuck and clean that area. If children use the garage to leave the house, it's sometimes something as simple as a small, bouncing ball that happens to land in just the right -- or wrong -- spot.
One thing to consider - assuming you have 2 springs and an opener, unless the other spring is quite new, you should replace it at the same time, first because it will probably break fairly soon anyway and changing two is only about $50 more than changing one, and because the springs on both sides should be of equal stiffness - if not, then the door will be unevenly weight compensated and try to open cockeyed, increasing wear and risk of damaging the motor.
If one of your door springs just broke and you are looking for instructions to decide if you can change the spring or springs safely and correctly, this page should help. DO NOT OPEN AND CLOSE YOUR GARAGE DOOR. Wooden garage doors are heavy and will probably damage or ruin the opener. The tops of steel doors often bend when operated with broken springs.
When cleaning the photo eye, you should take care not to scratch or damage the eye since it’s made of glass, similar to that of a camera lens. The photo eye itself is pretty small, only a few centimeters in diameter, but it can get dirty rather easily. To clean it, you’ll need a soft cloth and a mild, streak-free cleaner. Gently wipe away any dirt or residue that has built up on the eye and be careful not to oversaturate as excessive wetness can cause dirt to stick to the eye more quickly.
Warning! If the door is partially open and crooked, don’t touch it. Period. It’s a sign your door is off balance, and it’s usually caused by a problematic cable. It’s likely the door is still under tension from the spring, and one false move could send a 150-pound door crashing down, causing damage or injury, says Vincent Johnson, owner of Garage Door Doctor of Cypress, Texas. https://www.youtube.com/v/Z_eZc-kh40c&feature=youtube_gdata

Clearly there is a lot going on with your garage door and it takes trained and qualified experts to properly install, maintain, repair, and replace them. The experts and On Track Garage Door Services have the tools, skills, training to get your garage door fixed the first time. In addition we can help you fix your garage door affordably and offer many options from your basic garage door to custom wood styles. To find out how much your garage door repair will cost in Phoenix, Scottsdale, Mesa, Chandler or anywhere else, give us a call at 480-641-2301 or use our Contact Page.


Garage door springs can break for a variety of reasons. Extreme heat or cold, for instance, can stress the springs to the point of breaking, or it could be that normal wear on older springs could cause them to break. Whatever the situation, a broken spring can render your garage door inoperable. Your door will not be able to open or close when a spring is broken, and you should stand clear of your door until a professional can assess the situation and correct it.
If your garage door is equipped with only one torsion spring, it will be much harder to get your door open. You will need to get 2-3 people to help lift the door up because the full weight can be anywhere from 150 to 300 pounds. We don’t recommend lifting the door when the spring break's due to the danger of it falling on someone. If you absolutely must get your garage door open, raw strength is what you need. When you get the door in the up position, use vise-grips or a c-clamp on the track below the bottom roller to hold the door in the up position.

Sometimes, you’ll notice that your garage door closes all the way and then immediately goes back up instead of staying in the closed position. This issue usually arises with brand new garage doors that were just installed or older models that may need to be reset. If this happens, the most likely culprit is the open and close limit settings of your garage door opener. http://m.youtube.com/embed/Z_eZc-kh40c


Sears garage repair technicians are fast, with same-day, emergency repairs available in most areas. We can replace garage door broken springs, rollers, cables, hinges, sensors and weather seals. We can also adjust garage door tracks and springs to make sure your door operates smoothly. Having problems with your garage door opener? We can repair or replace that too. Check out our line of Craftsman Garage Door Openers. Craftsman is America’s #1 brand of garage door openers! 1 https://www.youtube.com/v/Z_eZc-kh40c&feature=share

Just like on a bike sprocket, your cables can sometimes become disengaged. Oftentimes, when a torsion spring breaks, the garage door cable will snap as a result. Sometimes, the cable will cause damage to a vehicle or wall, and if a person happens to be in the way of the cable it can cause serious harm. If you cables have snapped, you should call a professional to help you. See the video above. 
×