9.13 If you have a spring anchor bracket with a fixed steel bearing, check for wear at the point where the shaft and bearing race meet. The shaft needs to be free to slide sideways inside the bearing. File the shaft if needed. Lube the bearing. Notice that only one bearing is needed for two torsion springs. This bearing keeps the shaft from rubbing against the inside of the stationary cones and on the center bracket. Your garage door may not have a center bearing. If so grease the shaft where it will be rubbing the bracket and the insides of the cones.
Garage door springs don’t require extensive care and maintenance. However, they also can’t be left entirely to their own devices. Spraying the springs with WD-40 is a good place to start. It’s also a good idea to check the balance of the garage door every year. To do this, simply lift the garage door up about halfway and let go. If the springs are in good working condition, the door should remain still. If the springs are beginning to weaken, the door might sag or fall. By taking these basic steps, you can preserve your door springs for longer.
We want to hear from you and encourage a lively discussion among our users. Please help us keep our site clean and safe by following our posting guidelines, and avoid disclosing personal or sensitive information such as bank account or phone numbers. Any comments posted under NerdWallet's official account are not reviewed or endorsed by representatives of financial institutions affiliated with the reviewed products, unless explicitly stated otherwise. https://m.youtube.com/e/Z_eZc-kh40c
When cleaning the photo eye, you should take care not to scratch or damage the eye since it’s made of glass, similar to that of a camera lens. The photo eye itself is pretty small, only a few centimeters in diameter, but it can get dirty rather easily. To clean it, you’ll need a soft cloth and a mild, streak-free cleaner. Gently wipe away any dirt or residue that has built up on the eye and be careful not to oversaturate as excessive wetness can cause dirt to stick to the eye more quickly. https://youtube.com/e/Z_eZc-kh40c
They were quick, friendly, and highly professional. Little things like making me enter security code from the other side of the closed garage door revealed their attention to security They had to run to Home Depot to get a small block of wood to fix an existing problem with the door — They didn’t charge me extra. Quite unexpected & appreciated. 10 out of 10 https://m.youtube.com/embed/Z_eZc-kh40c
If the door won’t move at all because of an alignment issue, then this problem isn’t one that you should try to tackle yourself. A garage door professional will have the necessary equipment needed to safely realign and repair your garage door. Additionally, if the track misalignment is beyond repair, a professional can install a new garage door track for you. https://youtube.com/v/Z_eZc-kh40c?version=3
You may enter your information on this website, visit an in store associate or call our garage door repair team at the number at the top of this page. Within 24 hours you will receive a call from a local service provider to discuss your requested service. Afterwards, you will schedule a date and time for the service provider to come to your property.
Maybe the battery died or a spring broke, but you can't get into the garage to even see what the problem is. If the garage door is the only way in or out, or if you can't find the key to the door, you'll have to either find a way to break in or call a locksmith. As a preventative measure, it's smart to keep a spare key or install an emergency key release that would allow you to release the emergency disconnect to the operator so you can manually raise the door.
Homeowners have long been warned that torsion springs are extremely dangerous to work with and that replacing them must be left to a professional. But these claims are somewhat exaggerated. If you understand how they work, and you pay attention to what you're doing, you can replace them safely and surprisingly easily. Granted, they're a little spooky to work with at first (partly due to their reputation), but this is a good thing—you really don't want to forget that they're under tension. Thinking about every step — before you take it — is the key to staying safe. 

To make sure the job gets done right, our professional installers are local, licensed and insured. With a 9.7 out of 10 VOC score, our garage installers will exceed your expectations, provide reliable service, and install attractive garage doors that will transform your home’s appearance. All labor, products and installations are 100% backed by The Home Depot. Service you can trust.
I was disappointed with the pressure of a tub and shower that were plumbed with 1/2 supply lines (2nd floor). Could be low pressure from the street, but I want to replace with 5/8. Plus, I'd like to have 2 back to back showers, one inside and one outside. So, I had intended to bring a 1 supply to both, then branch up to valves and shower head with 5/8. Finally, I thought pressure from the street was typically 55 to 70 psi and I am concerned if pvc can take that.Any thoughts?

They were quick, friendly, and highly professional. Little things like making me enter security code from the other side of the closed garage door revealed their attention to security They had to run to Home Depot to get a small block of wood to fix an existing problem with the door — They didn’t charge me extra. Quite unexpected & appreciated. 10 out of 10 https://m.youtube.com/embed/Z_eZc-kh40c

Thread the cables and tighten the drums. Run the lift cable between the roller and the doorjamb. Slip the lift cable stop through the cable slot on the drum. Then, attach locking pliers to the torsion tube to secure it in place. Spin the drum to wind the cable into the grooves, then tighten the set screws. Repeat on the other side, leaving the locking pliers in place.[11]

Hiring a professional to handle garage door spring repair and replacement tends to be a much easier and safer option for homeowners. Removing or repairing garage springs can be a dangerous job, but professionals have the experience and equipment to do it safely and efficiently. Unless your springs only need a minor repair, such as lubrication or fixing a minor balance issue, be sure to call in a local garage door pro to do the job.


Our technicians are specially trained to handle a variety of garage brands, styles, and configurations. After arriving at your home, a Sears technician will diagnose the problem and walk you through the options for fixing it. Next, the technician will make any necessary adjustments or replace broken parts to ensure the door can be operational once again. We always attempt to complete repairs the same day of service, and your satisfaction is guaranteed. Our representatives are standing by for your call and are happy discuss pricing options.
	9.15 Install the bolts to secure the stationary center cones to the center bracket. Position the shaft here so it is the same distance from the header as the shaft is at each end. Finger-tighten the nuts until the stationary cones are flush against the center bearing plate. Forcing the cones by tightening the bolts may break a cone if it is catching on a bearing. Winding torsion springs with cracked cones can cause the springs to spin loose and the bars to fly. Secure the bolts.

Vincent was professional, informative, personable, efficient, and cleaned up his work area as he worked. I told him and now I am telling you... He my "Jordan" of garages. Give him a raise or at least a bonus. Thank you for sending him for my install. I am extremely pleased with my garage opener & with his install and information I am confident in its operation. Thank you.
Step 5: Check for loose hardware, and tighten as needed. On swing-up doors, check the plates where the spring is mounted to be sure the screws are tight, and tighten any loose screws. On roll-up doors, check the hinges that hold the sections of the door together; tighten any loose screws, and replace any damaged hinges. Sagging at one side of the door can often be corrected by servicing the hinges. If a screw hole is enlarged, replace the screw with a longer one of the same diameter, and use a hollow fiber plug, dipped in carpenters' glue, with the new screw. If the wood is cracked at a hinge, remove the hinge and fill the cracks and the screw holes with wood filler. Let the filler dry and then replace the hinge. If possible, move the hinge onto solid wood.
After you’ve ordered your new garage door, we’ll perform a site inspection to confirm your door size. We’ll contact you to schedule the installation, and our professional installers will do the rest. They’ll deliver your door, take down the old door, reconnect your opener if there is one, seal your perimeter and provide a final walk-through where they’ll clean up the area and haul away your old door. Additional fees for haul away may apply in some markets. We are happy to provide answers to questions you may have at the time of your garage door and opener installation.

Springs are one of the primary components in all garage door systems. Torsion springs are usually mounted horizontally over the door opening. As the door closes, cables add tension to the springs and as the door opens that tension is released. The opening of the door causes the springs to unwind in conjunction with the weight coming off the door. This achieves a natural buoyancy. However, as the door moves up and down over time and the cycle count rises, the steel in the torsion springs will grow weak and will no longer be able to create energy or lift your garage door.

Garage Door Repair Bracket Centennial Co 80016


Nearly every garage door comes with a warranty of some kind. Many companies claim they have a lifetime warranty but don't cover everything. Garage doors have many parts: rollers, cables, springs, door panels, etc. Find out what parts the warranty covers. When you read the fine print, you may find that the warranty does not cover warping, splitting, cracking, denting, or rusting and then limits parts to one year. When shopping you want to make sure you are comparing apples to apples.

Garage Door Repair Near Me Centennial 80015


Lower the door and dismantle it by removing the hardware. Lower a double door by recruiting at least two helpers to help with the weight, and place a 2×4 block under the door to prevent smashing a foot or finger when it’s lowered. Remove the sections one at a time by disconnecting the rollers and brackets. If you have windows, tape them to help control flying shards if they break. Then remove the old roller tracks and remaining hardware.
8.10 Double-check to make sure you have the correct wind on your new torsion spring. On the left side next to the winding cone the end of the spring wire should be pointing up if it is facing you. Notice, also, that the cone is red which usually designates right wind. Customers frequently call and explain that when they get about six turns on the springs they spin on the cones. This is due to installing the springs on the wrong sides of the center bracket.
Insulation, which increases energy efficiency and can help to lower utility bills, is crucial when a garage door is attached to the home. In this case, doors with high R-values are preferred. This means it has insulation that can keep the heat in. The higher the R-value, the better insulated your garage will be against outside noise and cold and hot air.
SNAP... bang... boom. That is the sound of a garage door torsion spring breaking. It can be a very loud noise that sounds like a firecracker or gunshot. Springs are rated for a certain number of cycles and are the first thing that will break in your garage door assembly. Broken springs are the #1 source of customer calls for garage door repair companies. If you have a broken spring, you should NEVER try to open the door, as it can be very dangerous. This repair should be left to a professional or someone with the right tools and skills.

10The type of garage door shown provides the necessary lift assistance with a “torque tube.” If you intend to use an opener, wait to install the tube. Otherwise, install the torque tube according to the manufacturer’s directions. Roll up the door about 4 feet to check for the alignment of the tracks, and make any adjustments. Then tighten all fasteners.
3. On an extension, or stretch type spring there is little you can do to extend the service life. On a torsion spring (the type that is wound on a bar rather than stretching out) you can help ensure a full cycle life by lightly lubricating the coils of the spring to reduce friction. If your garage door sees a lot of use and spring failure is an ongoing concern it can be addressed by selecting extended cycle springs. Discuss this upgrade when calling in for spring service, your service advisor will assist in making the correct choice for your needs.

Garage Door Repair Free Estimate Centennial Colorado 80015


Garage doors are the largest moving object inside your home. If you have a problematic garage door, it compromises the safety of your family and home. Overhead Door Company of Kansas City™ is a professional company you can count on. We provide you with quality service at a reasonable price. We offer FREE estimates on replacement garage doors and are spring replacement specialists. 24 hours a day 7 days a week we are your number one garage door repair service.
If your garage door goes up and down in a jerky motion, you might have one broken spring on a two spring system. Some garage door openers are strong enough to lift a door with only one good spring. The “herky jerky” motion is especially common with garage doors equipped with extension springs. It might be something as simple as lubricating your garage door pulleys, hinges, and rollers. When in doubt or if something doesn’t feel right about your door, call a service company to have it serviced.
2.3 Beware of older winding cones. These older Crawford and McKee torsion spring cones were made for 5/8" bars. Sometimes, however, the holes are too small for 5/8" bars. Whatever you do, don't use a 1/2" bar; instead, grind down a 5/8" bar to fit. I recently had a McKee spring let loose after winding because I used a 1/2" bar when my 5/8" bar wouldn't fit. Just before it let loose I was telling myself, "This is not safe." And it wasn't. The only safe way to replace these older springs is to make a winding bar for each hole of each cone. http://www.youtube.com/embed/Z_eZc-kh40c
	2.4 The same is true of Older Overhead, BarCol and Raynor torsion springs that have winding cones with inconsistent hole sizes. If you insert a 1/2" X 18" bar in some of these holes you can move the opposite end of the bar over four inches. Bars in newer cones move less than 1 1/2". I've had many of the older cones spin loose from my bars, the last one generating an $1800 emergency room bill. If your cones are like any of these, or if they have more than 2" of play, leave the job of installing torsion springs to a professional garage door mechanic.

If you have two torsion springs on your garage door, the good spring will most likely keep the cables on the drums when the other spring breaks. This makes it much easier to lift because the good spring will be pulling half the weight of the garage door. You can also use the garage door opener to help assist while someone lifts the door and acts as the broken spring. Use extreme caution when doing this to prevent damage to your garage door or injury to a person.

Garage Door Repair Emergency Centennial 80016


Lower the door and dismantle it by removing the hardware. Lower a double door by recruiting at least two helpers to help with the weight, and place a 2×4 block under the door to prevent smashing a foot or finger when it’s lowered. Remove the sections one at a time by disconnecting the rollers and brackets. If you have windows, tape them to help control flying shards if they break. Then remove the old roller tracks and remaining hardware.

If the engine of your garage door opener isn’t working properly, then your garage door probably won’t be working properly. If your garage door gets stuck and you hear a grinding sound coming from the garage door opener, then there’s a good chance that there is an issue with its engine. That issue is that the main drive gear probably needs to be replaced. The main drive gear is most common of the garage door opener’s components to fail. It is a plastic gear that takes some know-how to remove and replace, which is why you should strongly consider hiring a professional garage door repair service for this particular issue.


My garage door torsion spring broke so I decided to replace it myself. Shipping was next day. I got the torsion spring rod at a local hardware store. Easy to install once I figure out how to lock down the rod from moving and loosening the door cable on the side. Instructions tells you how to do it. Great replacement spring and save $$$ doing it myself. https://m.youtube.com/watch?v=Z_eZc-kh40c

If you are not sure if your door had the correct springs, we recommend that you weigh your door using an analog scale. From my own field experience I would estimate that at least 10% of the doors have the incorrect springs on them. In addition to this, most manufacturers spring their doors using a 20 pound window. We like to improve the garage door balance.
ryan was way more than early when he showed up. ryan gave me a straight up, not nonsensical "ah..ah..." like someone making up a story to listen to. direct and to the point, like a professional, gave me my options that i could present to the boss. the boss didn;t like the price of the new rollers. but she loves that it doesn't sound like a tank coming home from war. we were completely unprepared for this, so, it's good we got a guy like ryan.
Keep in mind, the pulley is often cycled through an enclosed casing that is difficult to lubricate directly. By applying enough lubricant to the pulley, you’re ensuring that the whole lifting mechanism is properly lubricated. Furthermore, a jam in this portion of the lifting mechanism is a time-consuming and potentially labor expensive repair that requires a service professional.
Overhead Garage Door was prompt in keeping the appointment, efficient in their work and professional when they worked on my garage door. The garage door was broken and the technician couldn’t have been nicer or quicker in getting the door repaired. I don’t know when I’ve had such good service from anyone! To add to that already wonderful service, I then received a follow up from the owner asking me about my experience and to make sure my door was working well. I highly recommend Overhead Garage Door for all of your garage door needs.
However, if after checking every other possibility, you still have a communication issue between your remote and your motor, it’s time to call in a professional. They have both the expertise and the specialized equipment to properly diagnose a wide range of motor sensor issues and will be able to help you take the next steps in either repairing your motor or having it replaced.
I am a relatively new homeowner and one of the first items that needed to be replaced was my garage door. I had the 1950s style with 2 separate doors and a support column down the middle . I bid out the work and OGD came in the lowest by far and provided a much higher quality door. I converted my door to a single door. Their team installed the support beam to brace the house and support the structure and installed the new door in a day. I had my first issue with door this week, by operator error. They came out same day and repaired the door and installed a keypad for me. I couldn’t be happier with the quality of the product and the customer service provided.
If your stuck garage door coincides with weather changes, you may need to adjust the pressure on the opener. Some openers have a force-adjustment mechanism that controls the force that's applied to operate the door. It's best to leave this adjustment to a garage door pro, as too much force may result in the door failing to stop when it should, posing a danger to people and objects in the door's path.
×