Install the center bearing and the right spring, then secure the cones. Slide the torsion bar to the left then add the center bearing. Slide the right spring onto the bar and press the bearing into the stationary cone. Connect both of the stationary cones to the center bracket with the nuts and bolts you removed previously. Remove the locking pliers or clamp from the center bracket.[10]
Like any mechanical part, garage door springs deteriorate due to normal wear and tear. Over time, the steel that makes up the springs weakens until they eventually break. Under normal circumstances, garage door springs have a life expectancy of 10,000 cycles of opening and closing. This equates to five to seven years, but along the way, there may be signs of problems that can occur before the springs actually stop working.

Garage Door Repair Guy Centennial Co 80015


When cleaning the photo eye, you should take care not to scratch or damage the eye since it’s made of glass, similar to that of a camera lens. The photo eye itself is pretty small, only a few centimeters in diameter, but it can get dirty rather easily. To clean it, you’ll need a soft cloth and a mild, streak-free cleaner. Gently wipe away any dirt or residue that has built up on the eye and be careful not to oversaturate as excessive wetness can cause dirt to stick to the eye more quickly.
Quite a few garage doors come with manual locks, especially older models, for added security for your house. These typically look like a knob or handle in the middle of your door with two bars running horizontally from each side. There may be a small button on the top or side of the handle that you can press to slide the bars across the doors, thus locking the garage door from the inside. It can be somewhat easy to accidentally hit that button, especially if you’re getting large objects out of the trunk of your car near the door.
Step 1: Check the metal tracks inside the garage. Look at the mounting brackets that hold the tracks to the walls. If they're loose, tighten the bolts or screws at the brackets. Working inside the garage with the garage door closed, examine the tracks for dents, crimps, or flat spots. If there are any damaged spots, pound them out with a rubber mallet, or with a hammer and a block of scrap wood. If the tracks are badly damaged, they should be replaced.
As mentioned in issue #2, garage doors are designed with a reversing mechanism that prevents them from crushing objects in their path. If you find that your garage door closes part way and then goes back up, this can be triggered by objects on the ground blocking their path such as garbage cans or toys. It could also be caused by a buildup of debris on the tracks that prevents the rollers from moving forward. This could include small items like rocks, gum or mud buildup. If the door hits even a small object on the track, it will go back up to avoid crushing whatever is underneath it.
While many sites may encourage you to save on garage door replacement costs by installing the door yourself, this is severely discouraged due to safety concerns and the installation techniques and tools required to properly and efficiently replace a garage door. When installing a new garage door, the range of prices also includes the labor performed by the professional garage door technician. These costs can include:

Our technicians are specially trained to handle a variety of garage brands, styles, and configurations. After arriving at your home, a Sears technician will diagnose the problem and walk you through the options for fixing it. Next, the technician will make any necessary adjustments or replace broken parts to ensure the door can be operational once again. We always attempt to complete repairs the same day of service, and your satisfaction is guaranteed. Our representatives are standing by for your call and are happy discuss pricing options.

"Springs get a lot of wear and tear because they handle the weight of the door," says Paul Cardone, owner of Garage Door Guru in Charlotte, North Carolina. "The type of spring you have depends on the type of door you have — the heavier the door, the more heavy duty the spring. They're full of tension and made of metal, so after so many cycles, they just snap and break."

Garage Door Repair Estimates Centennial Colorado


Home Depot local Service Providers are background checked, insured, licensed and/or registered. License or registration numbers held by or on behalf of Home Depot U.S.A., Inc. are available at homedepot.com/licensenumbers or at the Special Services Desk in The Home Depot store. State specific licensing information includes: AL 51289, 1924; AK 25084; AZ ROC252435, ROC092581; AR 228160518; CA 602331; CT HIC.533772; DC 420214000109, 410517000372; FL CRC046858, CGC1514813; GA RBCO005730, GCCO005540; HI CT-22120; ID RCE-19683; IA C091302; LA 43960, 557308, 883162; MD 85434, 42144; MA 112785, CS-107774; MI 2101089942, 2102119069; MN BC147263; MS 22222-MC; MT 37730; NE 26085; NV 38686; NJ 13VH09277500; NM 86302; NC 31521; ND 29073; OR 95843; The Home Depot U.S.A., Inc. is a Registered General Contractor in Rhode Island and its Registration Number is 9480; SC GLG110120; TN 47781; UT 286936-5501; VA 2705-068841; WA HOMED088RH; WV WV036104; WI 1046796. ©2018 Home Depot Product Authority, LLC. See sales associate for full list of product exclusions and other restrictions that may apply or call 1-800-HOMEDEPOT. Void where prohibited.
2.3 Beware of older winding cones. These older Crawford and McKee torsion spring cones were made for 5/8" bars. Sometimes, however, the holes are too small for 5/8" bars. Whatever you do, don't use a 1/2" bar; instead, grind down a 5/8" bar to fit. I recently had a McKee spring let loose after winding because I used a 1/2" bar when my 5/8" bar wouldn't fit. Just before it let loose I was telling myself, "This is not safe." And it wasn't. The only safe way to replace these older springs is to make a winding bar for each hole of each cone.	 http://www.youtube.com/embed/Z_eZc-kh40c

Your door’s torsion spring is located approximately one foot from the top section of your door when it is closed. It consists of two large coil springs, and is approximately the length of your arm. Its purpose is to balance the weight of your door so that a door weighing between 160 and 185 pounds is practically weightless to lift. As such, it makes it possible for a garage door opener to raise the door using only ten pounds of pressure.

Garage Door Repair Cost Centennial Co 80015


Garage door springs can —and will—break, and if you're anywhere near the garage when this happens, you'll know it. Nothing else sounds quite like a giant metal spring snapping under tension. Even if you don't hear it, you'll know the spring broke as soon as you (or your garage door opener) try to lift the door and finds that it now weighs twice as much. So faced with a broken garage door spring, the question is, can you fix it yourself?
Extension springs are long, lighter-weight springs that run perpendicular to the door and are mounted above the horizontal portions of the door tracks. These springs are tensioned by stretching out, using cables and pulleys, as with the torsion system. Because extension springs are merely suspended between two brackets (they are not mounted to a rod, like torsion springs), they must have a safety cable running through each spring. This helps contain the spring in the event of a breakage. Without the safety cable, a spring breaking under tension is a very serious safety hazard. If you have old springs that don't have safety cables, you should install them even if you aren't replacing the springs.
Using your drill, add tension to the torsion spring. This system uses a single spring for a double door, but many manufacturers use two springs for a double door. The painted line on the spring acts as a gauge for the number of turns you put on the spring. To keep the bar from turning while you’re adding tension, attach a locking pliers to the bar on both ends of the spring. Apply lubricant for garage doors to the spring.

Roberto was very courteous and explained the details of what he was doing. He also pointed out a repair I might consider having done (replacement of the bottom panel of my door) and asked the office to follow up with me on this. Someone did follow up with me and since replacement of the bottom panel is not an option and I would have to replace the door, I decided that I can wait.
The cost to repair a garage door is typically more affordable than installing a new garage door. Often, a garage door repair simply requires fixing a broken spring. The average cost to repair a garage door spring is $180, but prices range from $100 to $350 if the installer must disassemble the brackets to reach the springs. Common garage door repairs include lubricating or balancing the springs and installing safety cables that work as a backup for an extension spring system. Most homeowners can lubricate the springs on their own for the cost of the lubricant ($5 to $6), but many garage door contractors include lubrication services as part of their maintenance plans. Refitting existing springs to balance the door requires between 45 to 90 minutes to complete, with a price tag ranging from $75 to $110. Safety cable installation costs between $150 and $200.
Luckily, there is a bit of science to questions of garage door repair and replacement. That’s why we’ve put together this guide on when to replace a garage door. We’ll prepare you to compare repair vs replacement garage door costs. We’ll discuss the ways in which repairs are the most affordable option while also exploring those moments when replacement will in the end provide you with more value added.
One thing to consider - assuming you have 2 springs and an opener, unless the other spring is quite new, you should replace it at the same time, first because it will probably break fairly soon anyway and changing two is only about $50 more than changing one, and because the springs on both sides should be of equal stiffness - if not, then the door will be unevenly weight compensated and try to open cockeyed, increasing wear and risk of damaging the motor.

Garage Door Repair Free Estimate Centennial Colorado 80016


7.2 If the spring bracket is slotted, vise grip the bracket to secure the shaft in the bracket. This will keep the shaft from possibly falling out and causing injury or damaging the garage door or shaft. You can also secure the shaft with a cable tie. Remove the bushing from the cone and leave it on the shaft next to the center spring bracket. Often the bushing gets stuck in the cone and customers will call us about getting a new bushing until they discover it is still in the cone of the spring replaced earlier.
We want to hear from you and encourage a lively discussion among our users. Please help us keep our site clean and safe by following our posting guidelines, and avoid disclosing personal or sensitive information such as bank account or phone numbers. Any comments posted under NerdWallet's official account are not reviewed or endorsed by representatives of financial institutions affiliated with the reviewed products, unless explicitly stated otherwise.
2.4 The same is true of Older Overhead, BarCol and Raynor torsion springs that have winding cones with inconsistent hole sizes. If you insert a 1/2" X 18" bar in some of these holes you can move the opposite end of the bar over four inches. Bars in newer cones move less than 1 1/2". I've had many of the older cones spin loose from my bars, the last one generating an $1800 emergency room bill. If your cones are like any of these, or if they have more than 2" of play, leave the job of installing torsion springs to a professional garage door mechanic.

9.13 If you have a spring anchor bracket with a fixed steel bearing, check for wear at the point where the shaft and bearing race meet. The shaft needs to be free to slide sideways inside the bearing. File the shaft if needed. Lube the bearing. Notice that only one bearing is needed for two torsion springs. This bearing keeps the shaft from rubbing against the inside of the stationary cones and on the center bracket. Your garage door may not have a center bearing. If so grease the shaft where it will be rubbing the bracket and the insides of the cones.


Product was received in two days and was as advertised. Installing these myself saved around $150 but it took around 2-3 hours. I would imagine everyone's experience is going to be different. These springs appear to be heavier duty than the ones they replaced. I couldn't use the same slots for tension as the old ones and it was trial and error in adjusting the length of my pull cable until the door closed as it should. I need to replace the springs on my other garage door and would think that will take less than an hour based on what I learned from the first install.
My experience with Overhead Garage Door was exceptional! They were friendly and fast! I didn’t have to wait days to hear back from them and their prices were far better than that of their competitors top article. I would highly recommend Overhead Garage Door to anyone needing assistance with their door and especially if you’re in the market for a new one!
If you're like most people, your garage door is your primary entrance to your home. It's convenient to use and parking in the garage provides protection from the elements. Garage doors have several moving parts, including the door springs that help raise and lower the door. These springs do eventually break down, leaving the door inoperable. When this happens, it's time to repair or replace the damaged parts. This cost guide shows you what it costs to hire a professional to repair or replace any garage door spring.

Garage Door Repair Average Cost Centennial Colorado 80015


Instead, try other methods that might break the frozen connection between the door and the floor. For example, you can use a heat gun or hair dryer to melt the ice and free the door. Standard de-icing products can also work. And if you are careful not to damage the door or the seal on the bottom of the door, you can use a flat shovel or similar tool to chip away at the ice.
Depending on the type and location of the damage you might have an alternative to replacing panels, or entire garage doors. One solution to give new life to your garage door is repair. Small dents, rot, rust or holes can be repair without replacing. Depending on what wrong with the panel, average prices for repair are $130 for steel door repairs, $190 for wood, $170 for aluminum and $150 for fiberglass. Garage door panel repair can save homeowners money, but should be weighed against garage door panel replacement.
Determine the inside diameter of the spring and the size of the coils. Run a tape measure across the opening at one end of the spring. Carefully measure the inside diameter of the spring so you can provide the supplier with this information. Then, use a tape measure to find the length of 10 coils on the spring. Divide the length by 10 to determine the measurement of a single coil.[7]
A standard double garage door is 7 ft. high by 16 ft. wide. Standard single doors are 7 ft. high by 8 or 9 ft. wide. Because the doors are so large, few home centers and only some garage door stores keep many doors in stock, so expect to order one instead of buying it off the shelf. Garage doors are available in wood, fiberglass and steel. Steel doors, like ours, are light, maintenance-free, affordable, readily available, and have an insulating value as high as R-19.
×