Does your garage door stop when it is going up? Did you hear a loud bang, similar to a gun shot? Do the torsion springs above your door seem separated? If so, you might just have a broken torsion garage door spring. Torsion springs are located above the garage door and they are what lift the actual weight of the garage door. Most doors weigh between 150 to 250 pounds and without working springs, the garage door opener cannot lift the door. Attempting to use a garage door opener to lift a garage door with a broken spring can cause numerous parts on the opener to break.

Garage Door Spring, garage door houston, garage doors houston, houston garage door repair, garage door opener houston, garage door installation houston, garage door openers houston, garage door service houston, garage doors in houston, garage door repair in houston, garage door services houston texas tx, garage door torsion springs, Emergency Garage Door Repair

Containment cables. When old extension springs break, the springs and cables become heavy whips that damage cars and even injure people. To solve the whipping problem, manufacturers now offer containment cables that run through the center of side-mounted extension springs. If you have extension springs and don’t plan to replace your door, make sure the springs have these containment cables, or have a professional install them.

Weather conditions can make rails expand or contract slightly, which requires a little extra pressure from the opener to compensate. Turning the force-adjustment screw increases or decreases the force. However, adjusting the force is not something to play around with unless you are confident you know what you’re doing. The force adjustment signals the opener to stop and reverse when objects are detected in the closing path. Too little force and just about anything will trigger it to stop, but too much force and the garage door might not respond to resistance from something or someone in the path when the door is trying to close.
Once the lock switch has been activated, you can only control the garage door via the wall control unit. You may have forgotten to de-activate it after coming home from an extended period away, which is why the garage door seems to be stuck whenever you attempt to use your remote. Check to see if this is the case and simply unlock your remotes by pressing the lock switch again.

Garage Door Repair How Much Centennial Co 80015


If the door closes but then immediately pops open again, you'll need to check the limit settings, which help the mechanism determine how far to move the door in order to close it properly. If the settings are off, the door will hit the ground before the opener believes it should. It will assume that it has hit an obstacle and will automatically backtrack to avoid damage. Check the owner's manual or the buttons on the motor to adjust the limit settings. It may take some trial and error to get the setting just right. http://youtube.com/watch?v=Z_eZc-kh40c
9.14 Slide the springs to the bracket. Double-check to make sure you have the right wound spring on the left side and the left wind spring on the right side. Turn the springs until the ends are facing you. The wire at the ends of both torsion springs here at the bracket should be pointing down. At the winding cones at the opposite ends, the spring wire points up. If not, reverse the springs. About once a month we get a phone call from a do-it-yourself customer who begins the conversation with, "I wound the garage door spring to about six turns and the spring came loose from the cone." We normally refer them back to this step and suggest they switch their springs.

Garage Door Repair Free Quote Centennial Colorado


So if you’re worried that your door may be becoming more energy inefficient or if you’ve noticed a sudden spike in your heating costs, look at the weather stripping on your garage door. While you can replace it yourself, remember that effective weather stripping requires a tight seal, so if you’re unsure, you might save money in the long run by going with a professional garage door service


9.9 Go to the other side of the garage door and insert the end of the cable into the drum. Rotate the drum until the cable is tight. Slide the drum against the bearing and push the shaft to the right. The marks should line up. If they don't, figure out why and correct the problem. It could be a stuck cable, the garage floor may have shifted, or the vertical angle that helps support the bearing plate may have loosened and shifted. Many garage doors have been installed with a gap between a drum and a bearing plate. The cable drums should always be flush against the race of the bearings.
×