"Springs get a lot of wear and tear because they handle the weight of the door," says Paul Cardone, owner of Garage Door Guru in Charlotte, North Carolina. "The type of spring you have depends on the type of door you have — the heavier the door, the more heavy duty the spring. They're full of tension and made of metal, so after so many cycles, they just snap and break."
Using your drill, add tension to the torsion spring. This system uses a single spring for a double door, but many manufacturers use two springs for a double door. The painted line on the spring acts as a gauge for the number of turns you put on the spring. To keep the bar from turning while you’re adding tension, attach a locking pliers to the bar on both ends of the spring. Apply lubricant for garage doors to the spring.
If the garage door is broken or damaged, it can affect the feeling of the entire house. It’s not only an inconvenience, but it can also make your entire house feel less sophisticated and less functional. If you happen to be trying to sell your house, this can seem like a major detraction. Even if you’re only having guests over, you may feel as though you’re doing less than putting your best foot forward by having a broken garage door. http://www.youtube.com/watch?v=Z_eZc-kh40c&app=desktop
If you've installed a replacement door or two around your home, it seems pretty simple -- all it takes is tightening a couple of screws and you're done. Installing t­he largest door in your house, however, is not quite so simple. Garage door in­stallation, whether manual or automatic, can be difficult and dangerous. Manual garage door installation is much easier than automatic garage door installation, but the one you choose generally depends on what kind of door you have. https://www.youtube.com/watch?v=Z_eZc-kh40c
Replacement spring procedure took me exactly 1 hours including preparation and clean-up for double aluminum garage door. Watch the DIY video on Youtube, save $$, be careful with winding the torsion springs. Rule of thumb: 7' height door garage= 7' x 4 (each 1/4 turn) + 1 = 29 turns (1/4 turn), 8' height door garage = 8' x 4 + 1 = 33 turns (1/4 turn), and so on.... https://m.youtube.com/watch?v=Z_eZc-kh40c&feature=youtube_gdata
9.9 Go to the other side of the garage door and insert the end of the cable into the drum. Rotate the drum until the cable is tight. Slide the drum against the bearing and push the shaft to the right. The marks should line up. If they don't, figure out why and correct the problem. It could be a stuck cable, the garage floor may have shifted, or the vertical angle that helps support the bearing plate may have loosened and shifted. Many garage doors have been installed with a gap between a drum and a bearing plate. The cable drums should always be flush against the race of the bearings. https://www.youtube.com/attribution_link?a=Z_eZc-kh40c&u=watch?v=XXXXXX&feature=share
NEVER use screwdrivers, pin punches or pliers handles to wind or unwind a torsion spring. Trust us: This is the best way to wind up in the hospital. Don't even think about doing this job without a proper set of winding bars. You can buy a set of professional hardened-steel winding bars for about $25 from online suppliers. (Garagedoorpartsusa.com and stardoorparts.com are two online sources that sell winding bars, springs and other parts.) Professional winding bars work with 1/2-in. and 7/16-in. winding cones. If your winding cones have 1/2-in. openings, you can make your own winding bars by cutting a 36-in. length of 1/2-in.-diameter round bar stock in half (buy round bar stock from any hardware or home center). Just file a smooth bevel on each end so it slides into the winding cone holes easier.

Sears Garage Doors provides excellence in garage door repair services. With a Sears technician on the job, you’ll know that you’re getting the very best in industry experience and quality. Each of our employees undergoes a rigorous background check and extensive training to ensure quality results while on the job. Sears prides itself in offering some of the best experiences in customer satisfaction, service, and warranties. We believe in offering the best because we have the best customers. Call today to experience the best in what garage door servicing has to offer.
Overhead Door Company of Dallas/Fort Worth is North Texas' official Overhead Door distributor. For over 50 years we have been providing quality residential and commercial garage doors and fast and dependable garage door repair service not only to Dallas and Fort Worth, but to all cities in the DFW Metroplex. We are dedicated to 100% customer satisfaction.
Over time, our reputation has provided us with wonderful opportunities, such as supplying the rolling doors for Paul Brown Stadium while also serving as the service provider for Great American Ballpark. We are proud to be known in this city that we love. And as true Cincinnati fans, we are honored to play a small part helping the teams we root for!

Garage Door Repair In My Area Centennial Co 80015


Garage doors are able to move due to a counterbalance system that usually consists of a torsion spring. We often find incorrect springs have been installed which result in an unsafe door that you may not be able to open manually when needed. The balance of your garage door should be tested annually to reduce wear on your garage door opener and ensure it can be opened if an emergency situation arises. Because of the dangers involved with torsion springs, garage door spring repair and installation should only be done by experienced professionals like our Medics.

While many sites may encourage you to save on garage door replacement costs by installing the door yourself, this is severely discouraged due to safety concerns and the installation techniques and tools required to properly and efficiently replace a garage door. When installing a new garage door, the range of prices also includes the labor performed by the professional garage door technician. These costs can include:


While a new coat of paint can go a long way in improving the look of your garage door, the truth is that door design has come a long way in the years since garages were first installed in homes. Not only are newer doors more in line with current fashion trends, but they are also better sized for today’s cars. A new, contemporary door is a great way to get an immediate boost on the value of your home.

It is precisely on those coldest days of the year when you most need and appreciate the convenience of opening and closing your garage door quickly. Sadly, that's exactly the kind of day when moisture and cold can conspire to make this difficult. Garage doors can and do freeze to the garage floor. Sometimes it is just a minor icy connection between the two that can be broken when you hit the opener button. If the door refuses to budge on the first attempt, though, resist the urge to keep banging on the automatic opener button. This is likely to cause a more serious problem with the garage door opener—including, but not limited to, stripped gears, broken springs, and a burned-out motor on the opener.


Even though most of us are likely used to seeing this small spring in place on our garage door, we don’t often think too much about it, and we simply count on it working when we need it to. Unfortunately, it doesn’t last forever and will eventually need to be replaced. It’s best to be proactive and notice when it begins to look worn down before it actually breaks. Otherwise, you may find yourself trying to open the garage door to drive to work one morning, only to find that the door won’t open because the spring is broken.
If your garage door isn’t operating properly, the torsion springs are likely to blame. If you’re concerned about tackling this project on your own, consider hiring out the job to a professional. Otherwise, replace both the left and right springs at the same time to save yourself from having to do the job twice. Remove the old springs and measure them while they’re relaxed. Only then will you be able to order replacement parts and install the new springs. Replacing your own garage door springs takes only a little time and effort and can save you hundreds of dollars.
Garage Door Spring, garage door houston, garage doors houston, houston garage door repair, garage door opener houston, garage door installation houston, garage door openers houston, garage door service houston, garage doors in houston, garage door repair in houston, garage door services houston texas tx, garage door torsion springs, Emergency Garage Door Repair

Garage Door Repair Free Quote Centennial Colorado 80015


When you know you’re in range and the door still won’t open, check to make sure the antenna is hanging down from the motor inside your garage and nothing is blocking it. Your antenna must be free from any obstruction to clearly receive the signal to open and close the door. Also inspect the antenna for any signs of damage. If it looks like there has been damage to the antenna, you’ll need to call your garage door technician to come out and replace it.
A standard double garage door is 7 ft. high by 16 ft. wide. Standard single doors are 7 ft. high by 8 or 9 ft. wide. Because the doors are so large, few home centers and only some garage door stores keep many doors in stock, so expect to order one instead of buying it off the shelf. Garage doors are available in wood, fiberglass and steel. Steel doors, like ours, are light, maintenance-free, affordable, readily available, and have an insulating value as high as R-19.

Garage Door Repair Images Centennial Co 80016


Even though most of us are likely used to seeing this small spring in place on our garage door, we don’t often think too much about it, and we simply count on it working when we need it to. Unfortunately, it doesn’t last forever and will eventually need to be replaced. It’s best to be proactive and notice when it begins to look worn down before it actually breaks. Otherwise, you may find yourself trying to open the garage door to drive to work one morning, only to find that the door won’t open because the spring is broken.
Prices, promotions, styles, and availability may vary. Our local stores do not honor online pricing. Prices and availability of products and services are subject to change without notice. Errors will be corrected where discovered, and Lowe's reserves the right to revoke any stated offer and to correct any errors, inaccuracies or omissions including after an order has been submitted. https://www.youtube.com/watch?feature=youtube_gdata&v=Z_eZc-kh40c
DIYers are generally steered away from working with torsion springs because installed springs are always under tension. To safely remove a torsion spring, you have to control the tension by holding the spring with a solid metal winding bar, then you loosen the spring from the rod and manually unwind the spring using two winding rods. The spring is potentially dangerous until it is fully unwound. By contrast, extension springs have little or no tension when the garage door is fully open.

The national average for garage door repair cost is between $80 and $110. Some of the factors that affect your garage door repair cost are the type of springs (most often torsion or extension), the size and weight of the door, and the door material. Many garage door pros will charge a service fee to visit your house and determine the problem. Often, the service fee includes a set amount of labor. One example of this is an $80 service fee that includes the first hour of work plus testing and inspecting your garage door and garage door opener, while another pro may charge $150 for the same standard service call.   
It is very important that the replacement springs are calibrated for the weight of your door. Using the wrong size garage door springs will caused the to not function properly and could also cause the opener to break much quicker. Replacing extension springs can be very dangerous and if done wrong can harm someone using the garage door. Make sure you call the Garage Door Doctor to ensure your garage is repaired properly!
In order to replace your garage door spring(s), you will need to find the current measurements in order to accurately replace the spring(s). This should take about 3 minutes and you don't need to remove the springs or loosen the tension to measure them. Our springs are made to be a bit flexible, so you don't have to get it to an exact measurement. 
If you have a Wayne Dalton TorqueMaster system (pictured below), the springs will be inside a tube. The only way to determine if one is broken is to lift the garage door manually. If the door is heavy (roughly 60lbs for a double car door), you most likely have a broken spring inside the TorqueMaster tube. Another way to tell if you have a broken spring in your Wayne Dalton Torquemaster tube is if the door goes up and won't go back down.

Garage Door Repair Free Estimate Near Me Centennial Colorado


3. On an extension, or stretch type spring there is little you can do to extend the service life. On a torsion spring (the type that is wound on a bar rather than stretching out) you can help ensure a full cycle life by lightly lubricating the coils of the spring to reduce friction. If your garage door sees a lot of use and spring failure is an ongoing concern it can be addressed by selecting extended cycle springs. Discuss this upgrade when calling in for spring service, your service advisor will assist in making the correct choice for your needs.

Garage Door Repair Free Estimate Centennial Colorado 80015


One of the best ways to care for your springs is to check them over for wear. You can certainly look at them for damage, but sometimes the damage isn’t something that’s visible. In these cases, try lifting the garage door up from the ground. About halfway up, let go. If the door stays, the springs are still working perfectly. If the door sags or drops at all, this could be a sign that your springs are beginning to weaken and will need replacing soon.
While a new coat of paint can go a long way in improving the look of your garage door, the truth is that door design has come a long way in the years since garages were first installed in homes. Not only are newer doors more in line with current fashion trends, but they are also better sized for today’s cars. A new, contemporary door is a great way to get an immediate boost on the value of your home.
11.2a Raise the garage door slowly. Check the door balance. If you have the correct springs the door should stay down when closed, half way when opened half way, and open when opened. If the door will drop to the floor by itself from the halfway point, add 1/4 turn of tension to each of the torsion springs. If the garage door won't stay on the floor, and if it pulls itself up when stopped halfway, close the door and remove 1/4 turn of tension from the springs.
Overhead Garage Door was prompt in keeping the appointment, efficient in their work and professional when they worked on my garage door. The garage door was broken and the technician couldn’t have been nicer or quicker in getting the door repaired. I don’t know when I’ve had such good service from anyone! To add to that already wonderful service, I then received a follow up from the owner asking me about my experience and to make sure my door was working well. I highly recommend Overhead Garage Door for all of your garage door needs.
Adding a new garage door provides a dramatic difference in your home’s appearance. When neighbors pass by, when guests pull up, or when you return from work, your house will have a distinct beauty that makes it a landmark of the neighborhood. The unique look you’ve always imagined — as well as the material, the finish, and the insulation can be found in our wide selection of garage doors.
Order replacement springs. Many manufacturers and distributors only provide torsion springs to professionals, and won’t sell them directly to the customer. Luckily, they are available on the Internet, so search online to find replacement springs. Make sure they match the coil size, length, and interior diameter of the springs you removed. Also, be sure to order both a “left-hand” and a “right-hand” spring as the coils are wound in different directions.[8]
When it comes to installing garage doors and openers, The Home Depot has an unbeatable team of professionals dedicated to making sure your garage door project runs smoothly from start to finish. Your new garage door can be customized with a variety of features like unique color choices, window styles and hardware upgrades. We also offer options for your garage door opener including Smartphone control, Wi-Fi, battery back-up. The Home Depot installs garage doors and garage door openers with extended warranties that go beyond industry standards. Contact us today for a free in-home consultation.

Garage Door Repair Estimates Centennial Colorado 80016


Insulation increases the efficiency of your door and can lower your electric will. You need R-value garage doors. These type of doors keep out hot and cold air and also provide a sound barrier between the outside and your garage. Insulated doors use polyurethane or polystyrene foam as insulation inside the door. More information about garage door replacement cost.

NEVER use screwdrivers, pin punches or pliers handles to wind or unwind a torsion spring. Trust us: This is the best way to wind up in the hospital. Don't even think about doing this job without a proper set of winding bars. You can buy a set of professional hardened-steel winding bars for about $25 from online suppliers. (Garagedoorpartsusa.com and stardoorparts.com are two online sources that sell winding bars, springs and other parts.) Professional winding bars work with 1/2-in. and 7/16-in. winding cones. If your winding cones have 1/2-in. openings, you can make your own winding bars by cutting a 36-in. length of 1/2-in.-diameter round bar stock in half (buy round bar stock from any hardware or home center). Just file a smooth bevel on each end so it slides into the winding cone holes easier.
Although you should let professionals perform any tasks that require adjusting the tension on the springs, there are a few repairs you can do and maintenance tasks that extend the life of the door. One such repair is to tighten the nuts and bolts that hold the garage door and its track together. This also provides an opportunity to check the door and its parts for signs of wear and damage. You can also lubricate all the moving parts in the door, including the pulleys, bearings and springs. This shields the parts from dirt and helps reduce noise when the door opens and closes. Another job you can complete is installing an automatic garage door opener.
How much should a garage door spring replacement cost? The national average is between $200 and $300 for a professional to come to your house and replace two springs. On line sources suggest a higher price of over $700 and that you will save $500 or more by replacing springs yourself. This is simply not true. To find the cost for replacing springs in your area look for a reputable company through Yelp or the Better Busienss Bureau. If clicking a site's BBB logo doesn't take you to the BBB site, we advise purchasing your springs from a different company.
With over 300 independently moving parts, your garage door is a deceptively complex piece of equipment. To help prevent malfunctions and break-downs, it is a good idea to occasionally perform a garage door tune-up to keep all of these parts in good working order. A regular tune-up service by a Sears professional can prevent unexpected door problems and prolong the life of your existing equipment.
I'm looking about spanning 15' for a gazebo. trying to figure out what dimension beams I need. The Gazebo will be 15'x10'. How big will the beams have to be. at 1/2 the distance on 15' I will have a perpendicular beam running to carry 2x4's running parallel to 15' beam edge. I live in California in there with be no roofing material.. I will be using redwood for lumber Thanks
Nate was very courteous and professional and called to let me know that he was about 30 minutes from my house. I had purchased a new Sears garage door opener, but when Nate arrived at my home, he inspected the existing unit and told me that it was still in good shape except for a worn out part. Nate procured the new part and brought it to my home this morning. The unit was repaired in about 10 minutes! The existing unit was just over five years old, so I'm glad I will get some more use out of it.
The electronics should also be inspected before or after investing in the cost of replacing the garage door panel to make sure your door will operate properly. The sensors prevent the door from closing on someone's foot or a pet. If they don't work, someone could be injured. Also check to make sure the door opener works, since you could otherwise be locked out of your garage.
If your door has two springs, most professionals and research online says that replacing both springs is the best option. Most torsion springs are rated for 10,000 close/open cycles. If only one of your springs is broken, both springs are still recommended to be replaced. Considering that your second spring will break soon anyways, this added on fix is only going to cost you about $50 extra to assure that you don’t have to pay another service fee for a second visit.
Install the vertical roller tracks first by wrapping the curved lip around the rollers. The top of these tracks should be approximately 8 in. below the top of the top section. Wait to install the upper tracks until this step is complete. Check the level of the top section to make sure the tops of the vertical roller tracks are level with each other. The bottom of the roller tracks should be at least 1/8 in. off the concrete floor. After leveling and mounting these tracks, install the upper roller (horizontal) tracks.
Gather the supplies and tools needed for changing the springs safely. In addition to the torsion springs you'll need a minimum of one or two 10" vise grips, an adjustable wrench, and two 1/2" X 18" winding bars. Most hardware stores sell 1/2" X 36" steel rods that can be cut in half. You'll also need a firm ladder and a rag for cleaning your hands. A ruler and a file may also be necessary; a socket wrench and sockets would shorten the time required. Finally, make sure your garage is lighted well.
×