11.1 Many torsion spring replacement accidents occur from springs that are too strong. If the garage door stays on the floor by itself, remove the vise grip from the track. If the door is off the floor and the roller is against the vise grip, close the door with one hand and remove the vise grip with the other. If the springs are too strong, you have to restrain it from flying into the open position.

10.6 Here you will need to do three things at once. With your left hand, lift the bar just off the top of the door and pull it toward the center of the garage door. While lifting up and back, tap the top of the bar just under the winding cone with your other bar. Pulling the bar back toward the center of the door as you tap causes the spring cone to bind on the shaft and not slip back.
You can choose from three basic types of steel door: (1) steel only; (2) steel with insulation on the inside; and (3) steel on both sides with 1-3/8 to 2 in. of insulation. Other features that add to the cost are thicker insulation and windows, especially insulated windows. The do-it-yourself tensioning systems also add a little to the door’s cost. Be sure to specify exactly what you want.
3. On an extension, or stretch type spring there is little you can do to extend the service life. On a torsion spring (the type that is wound on a bar rather than stretching out) you can help ensure a full cycle life by lightly lubricating the coils of the spring to reduce friction. If your garage door sees a lot of use and spring failure is an ongoing concern it can be addressed by selecting extended cycle springs. Discuss this upgrade when calling in for spring service, your service advisor will assist in making the correct choice for your needs.

Garage Door Repair Free Estimate Centennial Colorado 80015


We also have a wide range of expertise repairing and installing both residential and commercial doors, meaning we can tackle any problem, large or small. We carry a wide range of doors from one of the industry’s leading manufacturers, Clopay, so you can make the choice that makes the most sense for your home and family while feeling confident that you are getting a door of the highest quality.
You may enter your information on this website, visit an in store associate or call our garage door repair team at the number at the top of this page. Within 24 hours you will receive a call from a local service provider to discuss your requested service. Afterwards, you will schedule a date and time for the service provider to come to your property.

Garage Door Repair Bracket Centennial 80016


If you have a Wayne Dalton TorqueMaster system (pictured below), the springs will be inside a tube. The only way to determine if one is broken is to lift the garage door manually. If the door is heavy (roughly 60lbs for a double car door), you most likely have a broken spring inside the TorqueMaster tube. Another way to tell if you have a broken spring in your Wayne Dalton Torquemaster tube is if the door goes up and won't go back down.
Install the stiffening strut on top of the top section of steel doors with the section lying flat. Then install the opener bracket that replaces the center bracket between the top two sections. While you’re working on the sections, protect them from scratches by putting carpet scraps on top of your sawhorses. Now, slide the rollers into the roller brackets.
If your garage door is equipped with only one torsion spring, it will be much harder to get your door open. You will need to get 2-3 people to help lift the door up because the full weight can be anywhere from 150 to 300 pounds. We don’t recommend lifting the door when the spring break's due to the danger of it falling on someone. If you absolutely must get your garage door open, raw strength is what you need. When you get the door in the up position, use vise-grips or a c-clamp on the track below the bottom roller to hold the door in the up position.
Roberto was very courteous and explained the details of what he was doing. He also pointed out a repair I might consider having done (replacement of the bottom panel of my door) and asked the office to follow up with me on this. Someone did follow up with me and since replacement of the bottom panel is not an option and I would have to replace the door, I decided that I can wait.

Although there are several tutorials detailing how to work with garage door springs, repairing or replacing garage door springs is a dangerous job best left to the professionals. The springs are under a significant amount of pressure, and a single mistake while working on the springs can cause serious injury or damage to people and property. Many homeowners also find that some stores refuse to sell garage door parts to amateurs, which makes it difficult to purchase the necessary parts for the repair or replacement job. Anyone who decides to attempt this work needs to spend time carefully learning each step of the process, purchase the necessary tools and take precautions to improve safety.

Garage Door Repair Installation Centennial Colorado 80016


I am a relatively new homeowner and one of the first items that needed to be replaced was my garage door. I had the 1950s style with 2 separate doors and a support column down the middle . I bid out the work and OGD came in the lowest by far and provided a much higher quality door. I converted my door to a single door. Their team installed the support beam to brace the house and support the structure and installed the new door in a day. I had my first issue with door this week, by operator error. They came out same day and repaired the door and installed a keypad for me. I couldn’t be happier with the quality of the product and the customer service provided.
I am a relatively new homeowner and one of the first items that needed to be replaced was my garage door. I had the 1950s style with 2 separate doors and a support column down the middle . I bid out the work and OGD came in the lowest by far and provided a much higher quality door. I converted my door to a single door. Their team installed the support beam to brace the house and support the structure and installed the new door in a day. I had my first issue with door this week, by operator error. They came out same day and repaired the door and installed a keypad for me. I couldn’t be happier with the quality of the product and the customer service provided.
Refrain from parking your car in the garage until the garage door is repaired. Additionally, try not to open and close the door while it’s in this condition. With that amount of possible force coming from the springs or cables, they could potentially damage your vehicle or other property in the garage as well as cause serious injury. It’s especially important that you and your family stay away from these cables or springs until everything is repaired.
Homeowners have long been warned that torsion springs are extremely dangerous to work with and that replacing them must be left to a professional. But these claims are somewhat exaggerated. If you understand how they work, and you pay attention to what you're doing, you can replace them safely and surprisingly easily. Granted, they're a little spooky to work with at first (partly due to their reputation), but this is a good thing—you really don't want to forget that they're under tension. Thinking about every step — before you take it — is the key to staying safe.

Garage doors are able to move due to a counterbalance system that usually consists of a torsion spring. We often find incorrect springs have been installed which result in an unsafe door that you may not be able to open manually when needed. The balance of your garage door should be tested annually to reduce wear on your garage door opener and ensure it can be opened if an emergency situation arises. Because of the dangers involved with torsion springs, garage door spring repair and installation should only be done by experienced professionals like our Medics.


Both types of springs are _loaded_, or under tension, when the door is closed. This gives them stored energy to help lift the door as it's being opened. When the door is all the way up, the springs are relaxed, or relatively so—they still may be under some tension. The mechanical difference between extension and torsion springs is that extension springs are loaded by stretching, or elongating, while torsion springs are loaded by twisting, creating torque.
Homeowners have long been warned that torsion springs are extremely dangerous to work with and that replacing them must be left to a professional. But these claims are somewhat exaggerated. If you understand how they work, and you pay attention to what you're doing, you can replace them safely and surprisingly easily. Granted, they're a little spooky to work with at first (partly due to their reputation), but this is a good thing—you really don't want to forget that they're under tension. Thinking about every step — before you take it — is the key to staying safe. http://m.youtu.be/Z_eZc-kh40c
Overhead Door Company of Central Jersey has been in the garage door industry since 1972. Our proficient service technicians offers the best installation, maintenance and replacement for your garage doors and parts. You can check our our Before and After residential garage doors photos for reference. Kindly click on "Schedule at-home appointment" below to get started.

When it comes to garage doors, functionality and safety are equally important in the eyes of Sears Garage Door technicians. Our associates know the importance of garage door safety and the hazards that a faulty garage door can pose for your family. To confirm that your garage door and opener operate safely, our technicians perform a 20-point safety check during maintenance calls and repair jobs. This safety check verifies that any repair work performed has been done correctly and that there are no lingering safety problems with your door and mechanisms. If our technician discovers any safety concerns, he’ll advise you on the best way to proceed with correcting the problem.
The springs are an essential component to your garage door in that they enable the door to be lifted or lowered easily, despite its weight. If either of the springs are broken, then the door will become stuck. There are two types of garage door springs – torsion springs and extension springs. Torsion springs are located near the top of the door, whereas extension springs are located on each side of the door. If your garage door uses torsion springs, check for a gap between the springs to identify whether they are broken. If you have extension springs, look to see if a piece of the springs are hanging from the side.

My wife and I began having our custom home built in the fall of 2002. We were able to subcontract many phases of the build process & we did all the painting. A highlight of the building experience was choosing precast concrete basement walls (produced in a controlled environment) and installed with great results by one of the TOH partners (Superior Walls). We got that idea based on watching a TOH episode on PBS a few years prior. It was quite the sight for our neighbors and us as the oversize flat bed truck arrived with an overhead crane and began the process of wall installation. It was kind of scary as the the wall sections were put in place. But without the TOH episode and the TOH seal of approval giving us confidence for the precast walls we would have chosen having the concrete walls poured on site. We have uncertain weather conditions here in Western NY during the late fall season. Who knows how pouring the walls on site would have gone. Thank you TOH for the precast wall episodes.
We want to hear from you and encourage a lively discussion among our users. Please help us keep our site clean and safe by following our posting guidelines, and avoid disclosing personal or sensitive information such as bank account or phone numbers. Any comments posted under NerdWallet's official account are not reviewed or endorsed by representatives of financial institutions affiliated with the reviewed products, unless explicitly stated otherwise.
10.4 Raise the second bar 90 degrees and insert the first bar. This is "three." Continue winding. If the spring shortens in length, unwind the spring and switch sides - the springs are on backward. Otherwise, continue winding until you reach a count of "30." This is 7 1/2 turns, which is normal for most 7' doors. Longer life springs are wound the same number of turns. Newer steel doors with only one strut on top often need only 7 1/4 turns. On 8' doors count to 34. Each time you insert a bar into the winding cone, listen for the click to let you know the bar is in all the way. Not inserting the bar all the way could cause the cone to explode. https://youtube.com/watch?feature=youtube_gdata&v=Z_eZc-kh40c
The new opener was installed yesterday and today for a while it wouldn't close properly. The customer service representative said they will probably have to reverse the sensors. However, no one could come out today (Friday) or tomorrow. She will call me by Tuesday of next week to schedule someone to come here. The customer service rep. and the technician were nice but as of now, my new garage opener is not working to my satisfaction.
×