5.1 With the cables still tight on the drums, mark the drums and torsion shaft at each end with a file or a marking pen. If at least one of the springs is still wound, don't touch the cable drums and don't grab the shaft. If the cable breaks, the drum could spin and the cable rip through muscle and bone. If the set screws aren't tight enough, the shaft could spin and cause injury.

On average, to have your springs replaced on your garage door will vary anywhere from $200 to as much as $400 if you were to hire a professional.  Breaking the costs down, the springs, depending on the part needed and the size, will cost about $20 to $60 each.  Add in the labor, which can be $45 to $85 per hour, depending on your location, can bring the grand total to the estimate noted.   A tilt-up door, on average, will be about 20 to 30 percent less than a roll-up door.
For Sears Garage Door Installation and Repair Services, making your garage door safe is as important as making it function well. For this reason, all of our repair services and tune-ups feature a 20-point safety check. Our technician will carefully examine your garage door panels, springs, sensors, safety release, hardware, track, and more. This ensures that, not only has our work been done well, but that your garage door poses no danger to your vehicles or family. Due to the intricacy of garage door systems, only garage service professionals should attempt to adjust, repair, or service door equipment.
77002, 77003, 77004, 77005, 77006, 77007, 77008, 77009, 77010, 77011, 77012, 77013, 77014, 77015, 77016, 77017, 77018, 77019, 77020, 77021, 77022, 77023, 77024, 77029, 77025, 77026, 77027, 77028, 77030, 77031, 77032, 77033, 77034, 77035, 77036, 77037, 77038, 77039, 77040, 77041, 77042, 77043, 77044, 77045, 77046, 77047, 77048, 77049, 77050, 77051, 77053, 77054, 77055, 77056, 77057, 77058, 77059, 77060, 77061, 77062, 77063, 77064, 77065, 77066, 77067, 77068, 77069, 77070, 77071, 77072, 77073, 77074, 77075, 77076, 77077, 77078, 77079, 77080, 77081, 77082, 77083, 77084, 77085, 77086, 77087, 77088, 77089, 77090, 77091, 77092, 77093, 77094, 77095, 77096, 77098, 77099, 77201, 77339, 77345, 77357, 77365, 77373, 77375, 77377, 77379, 77380, 77381, 77382, 77384, 77385, 77386, 77388, 77389, 77396, 77401, 77406, 77407, 77423, 77429, 77433, 77441, 77447, 77449, 77450, 77459, 77466, 77469, 77471, 77476, 77477, 77478, 77479, 77484, 77489, 77492, 77493, 77494, 77498, 77545, 77578, 77581, 77584, 77587,
While many sites may encourage you to save on garage door replacement costs by installing the door yourself, this is severely discouraged due to safety concerns and the installation techniques and tools required to properly and efficiently replace a garage door. When installing a new garage door, the range of prices also includes the labor performed by the professional garage door technician. These costs can include:
Nate was very courteous and professional and called to let me know that he was about 30 minutes from my house. I had purchased a new Sears garage door opener, but when Nate arrived at my home, he inspected the existing unit and told me that it was still in good shape except for a worn out part. Nate procured the new part and brought it to my home this morning. The unit was repaired in about 10 minutes! The existing unit was just over five years old, so I'm glad I will get some more use out of it. http://youtube.com/v/Z_eZc-kh40c?version=3

Sometimes, it's not possible to repair the garage door springs, and the only option is to replace them. Replacing garage door springs costs between $200 and $300 for a professional to complete the job. This includes the cost of the spring, which ranges from $40 to $100 for a torsion spring and $5 to $30 for an extension spring. Labor rates for this work average between $45 and $65, depending on the company and the region. The price can also go up or down depending on the type of door. Replacing the springs on a tilt-up garage door costs between $150 and $200, which is slightly lower than the same work on a roll-up garage door, which typically costs between $200 and $250.


We have had many concerns with our garage opener unit both safety issue and sleepless nights. At this time we are pleased that so far the unit is operating as it should.Hopefully we hope the issue of the unit opening by it self at early morning hours is solved. And if this is so, we want to Thank all involve in bring a satisfactory solution to this nightmare.
He is required to call in a service report for approval to repair, he reported the old springs and the broken door opener, obviously not well maintained (although installed in 1980 and operated until 2018) so the service company denied the claim and the service tech left with $125.00 just for showing up. The service company will no longer cover the door opener.

9.6 Bending the cable will help you avoid problems with the tip at the end of the cable catching on the end bearing plate and causing the cable to come off and the garage door to jam, cock, or fall. Check to make sure the cable is straight in the slot and not sticking out the side. Also the edge of the cable stop should not be pointing to the side as displayed. The cable tip should fit completely inside the drum, with the rounded part facing out so the tip can't scrape the end bearing plate.
Sears Craftsman Garage Door Openers are America’s favorite. We have several options to choose from that will fit your individual needs. Sears garage door opener selections includes 1/2 horsepower, 3/4 horsepower, belt and chain drive as well as the Craftsman Smart Control garage door opener which allows you to control and monitor your garage door even when you are away from home.

Poor lubrication is a very common and easy to fix explanation for why you might find your garage door stuck. You should properly lubricate your garage door's track, the opener chain and the springs every few months as part of regular preventative maintenance. Be sure to use Clopay's Garage Door ProLube or sillicone based lubricants. Do not use WD-40.


10.5 If the spring comes loose from the cone at about 6 turns, you are probably winding the spring backward because the springs are on the wrong sides. Switch the springs. Otherwise, after winding the torsion springs, you will need to stretch the springs and secure the winding cone. First, mark the shaft 1/4" beyond the winding cone with tape or with a file. We stretch the springs because the shaft floats horizontally between the flexible end bearing plates as the garage door operates. Although this may be as little as 1/4" the binding of the coils as the door closes often keeps the door from closing completely, especially when the springs and bearings are dry and need lubrication.
We lead busy and sometimes hectic lives. It’s easy for someone low on sleep and high on stress to accidentally bump into their garage door leaving a little damage. If you’re lucky it’s just an individual garage door panel that’s been damaged. This will leave you with the option of garage door panel replacement. There’s a chance it might cost you upwards of $150-200 to spot repair damaged garage door panel. If it happens to be an in-production model, they probably will be able to repair or replace the entire panel (if needed) for $250-400. Unfortunately if you’ve got an older model of garage door the panels may no longer be in production. This might seem like a disadvantage because you’ll end up having to just replace the entire door. Many times it’s actually easier and more cost effective to just replace the garage door.
×