In order to replace your garage door spring(s), you will need to find the current measurements in order to accurately replace the spring(s). This should take about 3 minutes and you don't need to remove the springs or loosen the tension to measure them. Our springs are made to be a bit flexible, so you don't have to get it to an exact measurement. 
Another scenario is the garage door goes up very slowly when using the automatic opener. Some garage door openers have DC motors that start off slow when opening and then kick into a higher speed. If you have a broken spring, the opener might stay in the slower speed due to the heavy weight of the garage door. If this happens to you, close the garage door and pull the emergency release rope. Next, try to lift the door. If it is really heavy, then you most likely have a broken garage door spring.
One of the best ways to care for your springs is to check them over for wear. You can certainly look at them for damage, but sometimes the damage isn’t something that’s visible. In these cases, try lifting the garage door up from the ground. About halfway up, let go. If the door stays, the springs are still working perfectly. If the door sags or drops at all, this could be a sign that your springs are beginning to weaken and will need replacing soon.
Slide the left spring onto the tube and add the cable drum. When your new springs arrive, put the new left spring (the 1 with the end facing up and to the left) on the torsion tube, making sure that the stationary cone on the end of the spring faces the center bracket. After sliding the new spring into place, replace the cable drum and insert the torsion bar into the left bearing bracket.[9]
Roberto was very courteous and explained the details of what he was doing. He also pointed out a repair I might consider having done (replacement of the bottom panel of my door) and asked the office to follow up with me on this. Someone did follow up with me and since replacement of the bottom panel is not an option and I would have to replace the door, I decided that I can wait.
Doors come with one or two torsion springs. If either spring is broken, the garage door opener may struggle to lift the weight of the door or fail to open the door at all. If a spring is broken, call a professional for service as these can be very dangerous to work with. Don’t try to open the door until a professional comes to inspect it and replace the springs. Springs can only be used for a certain number of open and close cycles, and over time they will eventually break and need replacing.
I purchased a garage door and opener and had HD install it. It was around $3600 and when the price increased by about $800 I called right away to pay it with no delay (these are all estimates written from memory). Anyway, I I bought the garage so that the front of the house would be prettier and it is but the old garage worked fine and I don’t even have a car in it so I don’t open and close it all and it actually only gets opened 2-3 times a month when a friend who stores their car there uses it. However, soon after the garage was installed, this friend told me the garage was working intermittently. When I called HD to come look at it, they said I would have to pay around $85 to have it looked at which didn’t make sense to me since it was brand new and almost immediately not working so it was likely a problem with the product or installation. HD would not provide immediate assistance to fix the problem, they insisted other steps which were unreasonable given it was a new garage and this request added great difficulty for me. Five months later after this back and forth calling to have someone from HD to just come and fix it, I went into the Huntington Beach store, spoke with Ryan who was polite and with little to say, he said I’ll put you on the list for an appointment and they will call in 24-48 to book a day and time. I was thankful. I also expressed my concern that I would not be charged for this visit and he said no unless it wasn’t covered under warranty. Two days later the installer called and said it will cost to around $95 just to show up. They arrived later that week, charged $95 and fixed the problem with no additional fee. If the garage was being used the way most garages are used and it was out of warranty, I could understand for a fee to cone out and look at it but because it stopped working almost Immediately and all the fuss and delay to have it fixed by HD was disappointing. When you gave me a quote then raised it by 20%% I paid immediately and without hesitation but this service was not reciprocated. I may have multiple projects at multiple sites but even if that weren’t the case, I would hope you would keep up your good costumer service history otherwise, your competitors willl slowly be better. Kindly return the fee charged for this service. Read less  http://www.youtube.com/v/Z_eZc-kh40c&feature=share

Determine the inside diameter of the spring and the size of the coils. Run a tape measure across the opening at one end of the spring. Carefully measure the inside diameter of the spring so you can provide the supplier with this information. Then, use a tape measure to find the length of 10 coils on the spring. Divide the length by 10 to determine the measurement of a single coil.[7] https://youtu.be/Z_eZc-kh40c
The new opener was installed yesterday and today for a while it wouldn't close properly. The customer service representative said they will probably have to reverse the sensors. However, no one could come out today (Friday) or tomorrow. She will call me by Tuesday of next week to schedule someone to come here. The customer service rep. and the technician were nice but as of now, my new garage opener is not working to my satisfaction. 

I called A1 Garage Door Service at 10:45am when I discovered my garage door was not working. I was given an arrival window of 12-2pm, and Technician Daniel arrived to my home at noon! That was amazing, and is not typical customer service today! Daniel was very knowledgeable and personable. I enjoyed talking with him, and appreciated how he worked with me. I never felt like Daniel was trying to rip me off. He explained all of my options very clearly. I will not hesitate to call A1 Garage Service for any future needs.
10.4 Raise the second bar 90 degrees and insert the first bar. This is "three." Continue winding. If the spring shortens in length, unwind the spring and switch sides - the springs are on backward. Otherwise, continue winding until you reach a count of "30." This is 7 1/2 turns, which is normal for most 7' doors. Longer life springs are wound the same number of turns. Newer steel doors with only one strut on top often need only 7 1/4 turns. On 8' doors count to 34. Each time you insert a bar into the winding cone, listen for the click to let you know the bar is in all the way. Not inserting the bar all the way could cause the cone to explode.
Install the center bearing and the right spring, then secure the cones. Slide the torsion bar to the left then add the center bearing. Slide the right spring onto the bar and press the bearing into the stationary cone. Connect both of the stationary cones to the center bracket with the nuts and bolts you removed previously. Remove the locking pliers or clamp from the center bracket.[10]

The track is secured with these little brackets and they're adjustable. There's a slot that it rides in so you can unscrew it here and adjust it if you need to. And you're going to have to pay attention and look at it closely to make sure it's in the right spot, but it's not that tricky and you can do it. And usually one side is out of alignment so you can compare it to the other and then adjust it as needed. https://youtube.com/watch?feature=youtu.be&v=Z_eZc-kh40c


One thing to consider - assuming you have 2 springs and an opener, unless the other spring is quite new, you should replace it at the same time, first because it will probably break fairly soon anyway and changing two is only about $50 more than changing one, and because the springs on both sides should be of equal stiffness - if not, then the door will be unevenly weight compensated and try to open cockeyed, increasing wear and risk of damaging the motor.

Garage Door Repair Free Estimate Centennial Colorado 80016


Poor lubrication is a very common and easy to fix explanation for why you might find your garage door stuck. You should properly lubricate your garage door's track, the opener chain and the springs every few months as part of regular preventative maintenance. Be sure to use Clopay's Garage Door ProLube or sillicone based lubricants. Do not use WD-40.


Using your drill, add tension to the torsion spring. This system uses a single spring for a double door, but many manufacturers use two springs for a double door. The painted line on the spring acts as a gauge for the number of turns you put on the spring. To keep the bar from turning while you’re adding tension, attach a locking pliers to the bar on both ends of the spring. Apply lubricant for garage doors to the spring.
While a new coat of paint can go a long way in improving the look of your garage door, the truth is that door design has come a long way in the years since garages were first installed in homes. Not only are newer doors more in line with current fashion trends, but they are also better sized for today’s cars. A new, contemporary door is a great way to get an immediate boost on the value of your home.
Electric Garage Door Openers – Service and repair of the electric garage door opener itself, including the lift mechanism that pulls the door up and guides it down. This is typically not part of the garage door itself and is serviced and repaired on its own interval. Typical service includes inspection, repair, adjustment, and lubrication if needed. Also, we typically inspect the mounting of the unit as well as its attachment to the door itself.
6.4 Test the fit of the bar in the cone before loosening a set screw. Insert one end of your winding bar into one of the holes of the winding cone. Pull down on the bar slightly to make sure the set screws are tight. Position your ruler between the bar and the garage door. Move the bottom of the bar from side to side and measure the play. It should be less than an inch and a half. If it is over 2" either get someone else to change your springs or have someone make some bars that will properly fit the cones. https://www.youtube.com/watch?v=Z_eZc-kh40c&feature=youtube_gdata
Furthermore, newer doors come with more improved security features, helping to improve the way you protect your home and loved ones. While older doors are easy to break into, whether through breaking the lift mechanism or even using a universal garage door remote, new doors come with many redundant security features, which will go a long way in deterring even the most ingenious burglar.
It you have a tilt-up door, you are looking at a $150 – $200 repair or replacement. If it’s a roll-up door it’s going to cost you more. Roll-up door spring repair or replacement is usually around $200 – $250 for a 2 car door. If the brackets need to be disassembled to remove the springs due to the shaft not sliding sideways enough it will cost you an additional $50 – $100.
The garage door opens and closes many times throughout the year, and something may blow inside. While it is usually something such as loose leaves or small amounts of dirt, the rails that the door travel along can collect this loose debris. Over time, the buildup of debris creates a blockage on the rails. Note where on the rails the door is stuck and clean that area. If children use the garage to leave the house, it's sometimes something as simple as a small, bouncing ball that happens to land in just the right -- or wrong -- spot.
A standard double garage door is 7 ft. high by 16 ft. wide. Standard single doors are 7 ft. high by 8 or 9 ft. wide. Because the doors are so large, few home centers and only some garage door stores keep many doors in stock, so expect to order one instead of buying it off the shelf. Garage doors are available in wood, fiberglass and steel. Steel doors, like ours, are light, maintenance-free, affordable, readily available, and have an insulating value as high as R-19.
×