Doors with extension springs have two sets of pulleys (which are sometimes called _sheaves_): one at the end of each spring and one at the top of the vertical door track. They also have two cables on each side. One cable attaches to the bottom of the door, runs up and over the pulley above the door and around the spring pulley and then attaches to the door track bracket. The other cables are safety cables that run through the middle of the springs and are fixed to a track bracket at both ends. These cables restrain the springs if they break under tension. All extension springs must have safety cables.
First, make sure your transmitter isn’t stuck under something that could be pressing on the button. For example, your transmitter may have fallen under your car seat and the button is accidentally being pushed by something heavy rolling around on your floor. If that’s not the case, you may also need to check your transmitter’s frequency. It’s possible your neighbors could be running their garage doors on the same frequency as yours, and as they drive by, they’re opening their garage door along with yours.
Your decision on whether to try and replace a broken spring may depend on what type of springs you have. Garage door springs come in two main types: extension and torsion. Identifying which type you have is easy. If your door system has a long, skinny spring running parallel to each horizontal door track, then you have extension springs. If your door has one or more beefy springs on a metal rod parallel to, and directly above, the door opening, then you have torsion springs. Both of these springs are found on standard sectional garage doors. If you happen to have an old one-piece, swing-up door with vertical springs at both sides, you also have a variety of extension springs, sometimes called side springs.
Slide the left spring onto the tube and add the cable drum. When your new springs arrive, put the new left spring (the 1 with the end facing up and to the left) on the torsion tube, making sure that the stationary cone on the end of the spring faces the center bracket. After sliding the new spring into place, replace the cable drum and insert the torsion bar into the left bearing bracket.[9]
8.5 Inspect the bearing. Lube it with motor oil, spray lithium, or spray lubriplate grease. Do not use WD-40. If the shaft is worn and the bearing is seized and you can't free it, replace the bearing. Or, if you have bearings labeled "ADH" we recommend replacing them. I find very few other bearings that need to be replaced. However, if you do need to replace the bearing and you do not have a new one, you can replace it at a later date. You'll find a quick way to do this at our End Bearing Plate Replacement instruction page.
Using your drill, add tension to the torsion spring. This system uses a single spring for a double door, but many manufacturers use two springs for a double door. The painted line on the spring acts as a gauge for the number of turns you put on the spring. To keep the bar from turning while you’re adding tension, attach a locking pliers to the bar on both ends of the spring. Apply lubricant for garage doors to the spring.
Quite a few garage doors come with manual locks, especially older models, for added security for your house. These typically look like a knob or handle in the middle of your door with two bars running horizontally from each side. There may be a small button on the top or side of the handle that you can press to slide the bars across the doors, thus locking the garage door from the inside. It can be somewhat easy to accidentally hit that button, especially if you’re getting large objects out of the trunk of your car near the door.
Keep in mind, the pulley is often cycled through an enclosed casing that is difficult to lubricate directly. By applying enough lubricant to the pulley, you’re ensuring that the whole lifting mechanism is properly lubricated. Furthermore, a jam in this portion of the lifting mechanism is a time-consuming and potentially labor expensive repair that requires a service professional.

Garage Door Repair Emergency Centennial Colorado 80015


Overhead garage doors weigh hundreds of pounds, and doors that are not properly maintained or which are equipped with older automatic garage door openers can be safety time bombs. All too common are the tragic stories of garage doors injuring or even killing children or pets who found themselves underneath a closing door. Modern automatic door openers with auto-stop and auto-reverse mechanisms have greatly reduced such accidents, but mishaps can still occur if the door and door opener are not properly maintained. 

Garage Door Repair How Much Centennial Co


10.8 After the cone reaches the mark, continue pulling the bar off the garage door and back toward the middle of the door with your left hand. Tighten both set screws 1/2 to 3/4 turns each after each screw first meets the shaft. This is the point at which you will feel the screw meeting resistance. If the garage door spring snakes after tightening the set screws, repeat the process and stretch the spring half as much as before. Residential torsion springs are stretched 1/8" to 1/4". Larger commercial and industrial overhead garage door torsion springs are stretched as much as an inch.
One thing to consider - assuming you have 2 springs and an opener, unless the other spring is quite new, you should replace it at the same time, first because it will probably break fairly soon anyway and changing two is only about $50 more than changing one, and because the springs on both sides should be of equal stiffness - if not, then the door will be unevenly weight compensated and try to open cockeyed, increasing wear and risk of damaging the motor. https://www.youtube.com/watch?v=Z_eZc-kh40c&feature=kp
Once you’ve identified where the ice is, use a hair dryer or some other heat source to melt and dry it. You want to be careful, because you don’t want to damage the metal in your doors by overheating it too quickly. However, some gentle heat will likely fix the problem. Just make sure to dry the moisture so that your door doesn’t freeze again over night.
If you want to do the repair yourself, get several phone estimates first, because rates vary widely among service companies. Most garage doors are heavy (200 to 300 lbs.), so call in three strong friends to help you lift the door and hold it open while you lock it in the full raised position with a locking pliers. Then move your vehicles and have your friends help you lower the door.

In order to prevent injury, garage doors automatically reverse if they come into contact with an obstacle. When the door closes halfway but then reverses for no apparent reason, this may be a sign that there is something preventing it from closing, something that you can't see. Check the tracks for stuff like dirt, rocks, bits of trash, or other debris. Give the tracks a wipe-down to dislodge anything that might be getting in the way.


9.4 Slide the end of the shaft into the end bearing plate. Tighten the set screws an additional 1/4 to 1/2 turns beyond the point you finger-tightened them. Add an additional 1/4 turn if you could not find the original set screw indentations in the previous step. Heavier wooden garage doors may require an additional 1/4 turn. Caution: Under-tightening the drums could cause the drum to slip and the door to cock or fall. Over-tightening the set screws could damage the shaft or drum, resulting in the same problems. This is a critical step.
I told several people that I planned on installing a garage door torsion spring after mine broke. ALL of them told me that it was too dangerous and a few feared for my life! Honestly it was one of the simplest home repairs I have ever done. That is thanks in large part to your very helpful installation video. Your videos on measuring springs etc. were also very helpful. All of the necessary details are there.

Garage Door Repair Images Centennial Co 80015


If a roll-up door, assuming you have not put in cabinets or anything that prohibits sliding the shaft sideways about 2-3 feet out of the spring to change it, then about $200-250 should do it for a 2-car garage door. If he has to disassemble the brackets to remove the springs because the shaft cannot slide sideways enough to get the springs on/off, then probably another $50-100.
I went on Garage Door Nation website to look at the conversion chart from 1 to 2 torsion springs. For my 1 spring, size 2"/0.250ID/30.5" length, they recommended 2 of 2"/0.207ID/24" length. I got this kit from Amazon for $64 with $11 overnight shipping even though I could get free shipping through Prime over the weekend, but I couldn't wait for 3 more painful days. Installed it followed YouTube video. Worked better than my old one, a lot quieter. Check the video if you want to install one yourself. Professional installation costs hundreds of $$$:

Garage Door Repair Cost Centennial Co


We are the leading supplier in the USA of these DIY bundle kits and make our springs in America - supporting veterans and American jobs. We offer you the same wholesale prices we sell to the experts and all of our parts are superior in quality to China made competitors or knock-offs found on sites like Amazon. Do not risk your garage door with inferior parts. Our springs win awards for a reason.

Garage Door Repair Bracket Centennial Co 80015


	7.3 Slide both torsion springs out above the top of the garage door toward the cable drums. Notice that there is only one bushing or bearing between the cones. Sometimes a single bearing is pressed into the bracket; other brackets have a single bearing or bushing that fits in either cone. Do not try to install a bushing or bearing in both of the stationary cones. You will risk breaking a cone. The purpose of the bushing is to keep the shaft from wearing against the spring anchor bracket. Only one bushing is needed to accomplish this. 

Garage Door Repair Images Centennial Co


When you're done watching this video you'll know how to determine whether the company you hired to replace your garage door spring installed the right size spring on your door. You'll also learn the consequences to your garage door opener if the wrong size spring is used. If you are having a problem with your garage door spring, the 2:30 minutes you spend watching this video is time will spent.
There are many steps to replacing torsion springs, but overall it's a simple, straightforward process. If you're inclined to attempt it, find a good online video tutorial (preferably done by a garage door pro) that walks you through the entire process, including how to buy the right size of springs. You can also buy new springs and any related parts online, along with the most important items that you need: the two solid-metal winding rods that you use to wind and unwind the torsion springs.
While there are times you may be able to fix the problem yourself, there are many reasons it may be best to leave the garage door repair up to the professionals. Knowing what’s wrong with your garage door may help you to determine if it is a problem you can tackle or if it’s time to call someone for assistance. To help you troubleshoot your garage door issues, here are the top 10 reasons your garage door won’t work.

10.13 Slowly pull down on the winding bar until the garage door rises 3" and the roller hits the vise grip on the track. The door will usually drop back down and raise the bar. If it doesn't, lift the end of the bar until the door closes. If the door comes up by itself when you hold the bar lightly, the springs are either over wound or they are too strong. You may need to remove 1/4 to 1/2 turns from the springs. If the door comes up on its own, you either have to many turns on the springs or you have the wrong springs. This can be very dangerous. We recommend getting professional help. Removing the winding bar could cause the garage door to knock you off the ladder.
Replacing a garage door panel can add significantly to the cost of a garage door repair. Panels run horizontally on sectional roll-up garage doors. They may be made of wood, vinyl, aluminum, fiberglass or steel. Garage door panels can become damaged from hail and other extreme weather, dents and dings, car accidents, and age. When deciding if you want to replace a garage door panel, it’s helpful to compare the potential repair cost to the cost of a new garage door. Panel replacement requires a pro with the proper tools as well as the new parts. With parts and labor you could be paying more than $500 for one new panel. In comparison, a new garage door may cost $800-$1,200 (on average) with installation. If there is a possibility your garage door was structurally compromised when the panel was damaged, have the pro assess whether it’s better to completely remove and replace the door, rails and framework to ensure your home’s safety. It may also be better to completely replace your door if it is severely rusted or dented; if the paint is peeling and fading; if the door model is outdated or you can’t find replacement panels; or if the panels or rails are structurally compromised.
On one-piece doors with side springs, you open the door to relieve the spring tension, and simply swap out the springs on the opener-arm mechanism; there are no cables or pulleys to deal with, and the springs have internal safety rods. Some doors have tensioners that maintain moderate tension when the door is open all the way, and on these you'll have to loosen the tensioner in order to remove the spring.
Adding a new garage door provides a dramatic difference in your home’s appearance. When neighbors pass by, when guests pull up, or when you return from work, your house will have a distinct beauty that makes it a landmark of the neighborhood. The unique look you’ve always imagined — as well as the material, the finish, and the insulation can be found in our wide selection of garage doors.
6.10 If the garage door comes off the floor when you pull down on the bar, and if the cone still won't loosen, tap the bar next to the cone with a hammer to force the cone beyond the swollen portion of shaft. Maintain a firm grip on the bar; keep it firmly inserted completely into the cone; and be prepared at all times for the cone to slip, break, explode or break free from the shaft and yank the bar down.
When you install a new garage door, replace all the hardware as well. If your automatic opener doesn’t have an automatic reversing system that includes photoelectric eyes, replace it. Doors with openers also require two extra pieces of hardware that you’ll see in Photo 4: a support strut (usually included in the door kit) and an opener bracket (not included). For doors with torsion springs located over the door, spend the $50 or so to have a garage door professional release the tension.
Keep in mind, the pulley is often cycled through an enclosed casing that is difficult to lubricate directly. By applying enough lubricant to the pulley, you’re ensuring that the whole lifting mechanism is properly lubricated. Furthermore, a jam in this portion of the lifting mechanism is a time-consuming and potentially labor expensive repair that requires a service professional. 

Garage Door Repair Companies Centennial Co


Both types of springs are _loaded_, or under tension, when the door is closed. This gives them stored energy to help lift the door as it's being opened. When the door is all the way up, the springs are relaxed, or relatively so—they still may be under some tension. The mechanical difference between extension and torsion springs is that extension springs are loaded by stretching, or elongating, while torsion springs are loaded by twisting, creating torque.

Garage Door Repair In My Area Centennial Co


With Sears Garage Doors you can feel confident that you are getting the very best for your home and your family. All of our technicians are background checked, professional, and committed to complete customer satisfaction. The "best" is standard for all new Sears Garage Doors, Sears Garage Door Openers and Sears Garage Door Repairs. We offer some of the best warranties available in the industry, the best design advisors, the best technicians, and the best products. We may be a little biased, but we also believe we have the best customers. Go ahead, choose to be part of the best.

Garage Door Repair And Installation Centennial Colorado 80015


The problem is that one of the garage doors "catches" (i.e. stops) while going up at about 2 feet off the ground ~90% of the time. When the button is pressed again, it goes all the way down. This cycle can be repeated ad nauseum, or I can give the door a gentle tug upward just before the "Sticking" point, and this will give the door enough "impetus" to make it all the way up.
The nucleus of any garage door system is its opener. Easily overlooked, garage door openers are highly complex pieces of equipment, often containing dozens of intricate parts that work simultaneously with one another to consistently raise and lower your door. You'll know that you're getting the best from Sears as it's the home to America's #1 Garage Door Opener Brand, Craftsman*.
If your garage door is equipped with only one torsion spring, it will be much harder to get your door open. You will need to get 2-3 people to help lift the door up because the full weight can be anywhere from 150 to 300 pounds. We don’t recommend lifting the door when the spring break's due to the danger of it falling on someone. If you absolutely must get your garage door open, raw strength is what you need. When you get the door in the up position, use vise-grips or a c-clamp on the track below the bottom roller to hold the door in the up position.
Does your garage door stop when it is going up? Did you hear a loud bang, similar to a gun shot? Do the torsion springs above your door seem separated? If so, you might just have a broken torsion garage door spring. Torsion springs are located above the garage door and they are what lift the actual weight of the garage door. Most doors weigh between 150 to 250 pounds and without working springs, the garage door opener cannot lift the door. Attempting to use a garage door opener to lift a garage door with a broken spring can cause numerous parts on the opener to break.

Garage Door Repair Centennial Colorado 80016


Because garage doors are large, heavy, and mildly complicated, most people who buy them take advantage of these services. But, if you’re pretty adept at DIY tasks, you can save some money and enjoy the satisfaction of doing the job of installing a sectional garage door yourself. (Sectional garage doors travel up and down on rollers that ride along tracks at each side of the garage doorway.)

Garage Door Repair Companies Centennial Co 80015


Looking to repair your garage door opener? Common problems could range from issues with the remote or wall switch that control the garage door opener to more serious issues like a grinding noise coming from the opener itself. If you need help with repairing your garage opener, schedule a repair appointment today! We repair all major brands and have same-day availability in most markets, so we can get your garage door opener repaired and running smoothly. To learn more about the cost of repairing garage doors, visit our garage door and opener installation and repair cost guide.

Loosen the set screws while holding each spring with a winding bar. Position a sturdy ladder to the side of the springs, rather than working directly in front of them, for safety reasons. Put on eye protection and leather gloves. Push a winding bar into the bottom hole of the winding cone on the outside of 1 spring. Use a wrench to loosen the 2 set screws. Keep a firm grip on the bar as the the spring will expand powerfully as the screws are released. Repeat on the other side.[2]
However, in addition to potentially causing injuries to the under-prepared DIYer, a malfunctioning door can become a safety hazard to you and your family. Keep in mind, according to the National Electronic Injury Surveillance System (NEISS), over 13000 people checked into hospitals with garage related injuries in the United States in 2007. You don’t want to turn a loved one into a statistic just to save a few dollars!
Luckily, your garage door is a pretty sound investment. According to Garage Wow Now, garage doors were ranked in the top three for home improvements whose costs are recouped through increased home value. Similarly, realtors regularly increased the list price of a home with a new garage door by 1 to 4 percent! That means, if you spend $2000 on a new garage door, you can increase the value of your home by almost $8000 if you have a $200,000 home. Furthermore, compared with the other two highest rated improvements — siding replacement and deck installation — a garage door replacement is far more affordable.
Although there are several tutorials detailing how to work with garage door springs, repairing or replacing garage door springs is a dangerous job best left to the professionals. The springs are under a significant amount of pressure, and a single mistake while working on the springs can cause serious injury or damage to people and property. Many homeowners also find that some stores refuse to sell garage door parts to amateurs, which makes it difficult to purchase the necessary parts for the repair or replacement job. Anyone who decides to attempt this work needs to spend time carefully learning each step of the process, purchase the necessary tools and take precautions to improve safety.

Garage Door Repair In My Area Centennial 80016


A standard double garage door is 7 ft. high by 16 ft. wide. Standard single doors are 7 ft. high by 8 or 9 ft. wide. Because the doors are so large, few home centers and only some garage door stores keep many doors in stock, so expect to order one instead of buying it off the shelf. Garage doors are available in wood, fiberglass and steel. Steel doors, like ours, are light, maintenance-free, affordable, readily available, and have an insulating value as high as R-19.
×