Replacing torsion springs is done with the door closed. You start by carefully unloading all of the springs (most standard-size doors have two; any broken spring will already be unloaded), using the winding bars. Then, you unbolt the springs from the central rod bracket, disconnect the cables from the pulleys, and loosen the pulleys and slide them off of the rod. Next, you swap out the springs, reinstall the pulleys and cables, and secure the inside ends of the springs to the central bracket. Finally, you wind up both springs (securing them with two setscrew bolts on the winding cones) and test the door for proper spring tension. Often, springs need an extra quarter-turn or two to get the door balance just right.
If your photo eyes are clean and the door still isn’t closing, the next thing you’ll need to do is check the alignment of the eyes. The eyes should be pointing in exactly the same direction and at the same angle. If they’re off, they won’t register that the other one is there, and it’ll assume something is in its path, causing the door to stay in the open position. When checking the alignment, measure the height of each photo eye from the ground. Use a level to make sure they’re pointing directly across at each other at the same angle. A laser level will make this part a little easier, but if you don’t have one, a regular level will work as well.
Door styles - in addition to the styles just mentioned, it is important to also consider additional features such as windows across the top of the door to provide light inside of the garage, the use of steel or wood frames to give decorative doors added security and stability, and insulation which can reduce energy costs in the attached garage by an impressive 15 to 20%; and
Good response time and service; Question - I googled to find the Sears Garage Door repair phone number. During the conversation, I was unsure if this was "Sears" or a "contractor service" or other service. I had to ask if this repair person was coming from "Sears" or an independent repair. I was concerned until the service man arrived in a sears truck wearing Sears apparel. You might want the process to be more clearly identified as Sears.
11.2b If the springs you installed are too strong, and if you wind the springs the correct number of turns, the door will not stay down nor half way. The garage door will be hard to close. DO NOT REMOVE MORE THAN HALF A TURN OF SPRING TENSION TO CORRECT THE PROBLEM. Here's why. If you remove 3/4 of a turn to get the door to stay closed, and then if you open the door, it will get heavier as you open the door, and once open, the cables will come off the drums. This could create as much as a day's extra work. It could also cause door damage and/or result in serious injury. Do not use the door! Get different springs!

Garage Door Repair Estimates Centennial Co


Once you’ve decided it’s time to replace your garage door — whether the result of malfunctions or just seeking to modernize your home’s exteriors — you may be wondering how much a garage door replacement costs. While these numbers are often determined by several factors, including the materials and labor involved, on average, a garage door replacement can cost just over $1,000 but could range from about $300 to over $2,000.
Most homeowners never know they have a broken garage door spring until they try to leave their home. You go in the garage to open the door, push the wall button, and the door only goes up 6”. The reason for this is the garage door opener force or sensitivity has activated, causing the opener to stop pulling the door up. This is a safety feature built into most garage door openers. It is actually a good thing when the open force activates to prevent any damage to your garage door or opener.
Received all items as indicated, I would recommend purchasing a metal center bearing also, other Than the plastic that this comes with. Install was easy and strait forward. hardest part was finding how many turns to tighten those springs?? I used a general rule of thumb of a full turn for every ft. Of door. 4 quarter turns equals 1 full turn. I found that 26 balanced the door perfectly. These springs seem a little smaller than what was there however, the coil itself is the same. (Pic) After installing, I recommend oiling the springs with some motor oil. This will help with rust and noise. Good luck with yours, it's worth the work for the saving!!

When a spring breaks on a garage door an immense amount of energy being displaced. Torsion springs are mounted over the garage door and they have a shaft running through the middle. When they break, the spring unwinds in less than a second and creates a loud noise due to the coils spinning on the shaft. Based on customer feedback, it can be quite startling.

Garage doors eventually begin to break, look terrible and pose safety risks. How old is your garage door? Have you ever had a safety inspection performed? Garage door safety should always be a top priority as it could cause serious injuries and cost you the expense and trouble of personal injury lawsuits. Our blog will show you what you need to know about garage door safety inspections to assist you with the inspection and upgrades of your home's garage door. Hopefully, what we show you will help to keep your friends and family safe from harm when they visit you.
Torsion springs have three advantages over extension springs: They’re quieter, safer and easier to fine-tune. Torsion springs are quieter because you don’t have a spring knocking against a roller track. They’re safer because when a spring breaks, it usually stays on the bar. Finally, you can fine-tune the tension on a torsion spring so the door is perfectly balanced. Setting the tension on torsion springs has always been very dangerous, but torsion and extension spring systems with easy, do-it-yourself tensioning (Photo 7) are available. If you don’t use one of these DIY-friendly, easy tensioning systems (Clopay EZ-Set Spring and Wayne-Dalton TorqueMaster are two brands), you should hire a professional to release and set the tension on a torsion spring.

If you have a garage door opener and you suspect a spring has broken, do not disconnect the opener from the door (by pulling the red emergency release handle) while the door is open. If you do, the door can come crashing down under its nearly full weight, with nothing to stop it. This is an extremely dangerous situation. It is never safe to leave the door open when a spring has broken because someone might try to close the door without realizing how heavy it is. Or, they might pull the emergency release handle on the opener.


To evaluate whether the problem lies with the door or the automatic opener, make sure the door is in the fully closed position, then disengage the opener trolly from the door by pulling the emergency release cord. Try to lift the garage door by hand. If the door opens smoothly by hand, the problem is with the opener. If the garage door still only opens halfway, the problem is with the door.
Even though most of us are likely used to seeing this small spring in place on our garage door, we don’t often think too much about it, and we simply count on it working when we need it to. Unfortunately, it doesn’t last forever and will eventually need to be replaced. It’s best to be proactive and notice when it begins to look worn down before it actually breaks. Otherwise, you may find yourself trying to open the garage door to drive to work one morning, only to find that the door won’t open because the spring is broken.
All measurements should be in feet and inches. Step 1, measure across the existing door or desired space for the width, then up and down for the height. The rough opening of your space should be the same size as the door. Step 2, measure the sideroom, which is the space beside your door. Measure the width of the left side, and then the width of the right side. Step 3, measure the space above the door, which is called the headroom. Measure the height of the distance between the top of the door opening and the ceiling. Step 4, measure the ceiling, which is called the backroom. You’ll need to measure the distance of the garage door opening toward the back wall of your garage. You should have 6 total measurements in all once you’ve finished measuring the space. Keep in mind that having an automatic garage door opener installed might call for additional backroom or ceiling space.
A new garage door can add serious curb appeal, not to mention myriad home safety benefits. The cost of a new garage door will vary based on the type of garage door you want and the materials it will be made of. You can purchase a new garage door and have the pros install it for you, but proceed with caution as many installers won’t guarantee their labor if you didn’t purchase the garage door through their company. A new door (without installation) may cost anywhere from $200 to $4,000 or more, depending on size, brand and materials. Here are some examples of average new garage door costs, including installation:  
Garage Door Spring, garage door houston, garage doors houston, houston garage door repair, garage door opener houston, garage door installation houston, garage door openers houston, garage door service houston, garage doors in houston, garage door repair in houston, garage door services houston texas tx, garage door torsion springs, Emergency Garage Door Repair
While you can certainly redo any security features on your garage door, it is often wise to replace the entire door if in fact that is the way a burglar gained access to your house. A new security code may seem like enough, but you don’t know how the thief figured out the old code in the first place. If the motor was disengaged, the issue might be a design flaw in the door itself. The best way to ensure that the thief doesn’t return or another thief doesn’t take advantage of the same unknown security weakness is to install a new door. Again, doing so with give you access to the kinds of robust security features that are being installed and implemented in the newest garage doors on the market.
After removing the old batteries, make sure the plus and minus signs line up with the plus and minus signs on the inside of the transmitter. Otherwise, the new battery won’t work in the transmitter, and it could give you a false sign that something else may be wrong. Once the battery is in place, test the transmitter, and if it works, replace the transmitter door.
While a sudden issue is usually easily repaired, a consistent issue that has gone unaddressed for months or years will likely require a total replacement. The problem is that garage doors have a number of heavy, powerful moving parts. If the door is working as it is designed, it can open and close hundreds and hundreds of times without issues. However, if there is even a small issue in the lifting mechanism that repeatedly influences the movement of the door, you will soon find that the damage caused over those hundreds of lifts can’t be fixed.
Looking to repair your garage door opener? Common problems could range from issues with the remote or wall switch that control the garage door opener to more serious issues like a grinding noise coming from the opener itself. If you need help with repairing your garage opener, schedule a repair appointment today! We repair all major brands and have same-day availability in most markets, so we can get your garage door opener repaired and running smoothly. To learn more about the cost of repairing garage doors, visit our garage door and opener installation and repair cost guide.
The U.S. Consumer Product Safety Commission says that about 30,000 injuries linked to garage doors are now reported every year in the United States. Many of these injuries have involved bruised or broken extremities. However, some have included serious shoulder, back, and head injuries leading to permanent disability or even death. What is the cause of these garage door injuries? One leading cause has been homeowners trying to repair or replace their own garage door springs.
The Torquemaster system has a lock built into each side on a double car door that will activate when a spring breaks causing the door to lock in the up position. It is very simple to deactivate this lock and get your door closed. But, you can guarantee you have a broken spring inside the Torquemaster tube on the side where the lock activated. You will need the spring inside replaced or have it converted over to a standard torsion spring set up, which is what we recommend and a service we perform quite frequently. A standard torsion spring will last 3 times longer than the small spring inside the Torquemaster tube.
As we’ve mentioned before, springs are installed within your garage lift mechanism in order to help lift the door. Because doors are so heavy, the lift motor would undergo far more significant wear and tear if it had to lift the full weight of the door every time you opened it. Furthermore, in order to ensure that you can open your door even if you lose power in your home, springs allow you to lift the door by hand when the motor is disengaged.
In this article, we’ll tell you the difference between a safe door and one that’s unsafe. We’ll also give you the helpful tips you’re not likely to find in the manufacturer’s instructions to correctly, and safely, install a new garage door with a torsion spring and do-it-yourself tensioning. Installing a new, double garage door yourself will save you several hundred dollars and should take eight to 12 hours if you’re fairly handy. You can do most of the new garage door installation project yourself, but you should recruit help for removing the old door.
×